I O Error Dev 08 11
Can't access the devices. Here is the the paste from self-test logs: smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-51-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Fujitsu Can anyone tell me what I can try to recover those drives? even if it's brand new?
Thanks WonderWoofie. Regards,Pedro Sousa 1366-238940-1432314 Back to top Ilya Chistyakov Members #10 Ilya Chistyakov 43 posts Posted 09 February 2011 - 10:49 AM I have a same problem. A reboot fixes the problem, but it happens again. Could you please be more specific? http://askubuntu.com/questions/424580/i-o-error-dev-sda-sector-xxxxxxxxxx
I O Error Dev Sda Sector Linux
If Selective self-test is pending on power-up, resume after 0 minute delay. Perhaps the drive-power are gone? #4 udo, Nov 11, 2011 Last edited: Nov 11, 2011 check-ict Member Joined: Apr 19, 2011 Messages: 77 Likes Received: 0 I can try a When I checked /mnt/backup1, wich isn't used for snapshot back-ups, i noticed it was also mounted as read-only.
General Purpose Logging supported. After rebooting into the installed system, however, I keep getting error messages like the one shown above. Selective Self-test supported. Blk_update_request I/o Error Ubuntu Central europe and the national color black Data Loader v38 (Winter 17) What could make an area of land be accessible only at certain times of the year?
Bad sectors are not hardware problems if I understand the howto right; are they?The howto suggests identifying the respective bad block and overwriting it with zeros (or with whatever) using dd. End_request I/o Error Dev Sector To run via the the command line, do the following sudo smartctl -i /dev/sda Make sure SMART is turned on. check-ict Member Joined: Apr 19, 2011 Messages: 77 Likes Received: 0 Hello all, I'm running Proxmox 1.8 on a Supermicro server with 8 hot-swap bays with hardware raid and 2 normals SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode.
Is my hdd defective? Blk_update_request I/o Error Dev Sda Sector We think our community is one of the best thanks to people like you! Galiza Nação! You can look with smartmontools: Code: apt-get install smartmontools smartctl --all /dev/sdb smartctl --all /dev/sdc Perhaps something strange with the mainboard (because of problems with both disks on the same time)...
End_request I/o Error Dev Sector
The disks are not visible anymore. you could try here SCT capabilities: (0x303f) SCT Status supported. I O Error Dev Sda Sector Linux Use the FAQ Luke Top 1885 Posts: 110 Joined: 2014/10/25 13:33:03 Re: blk_update_request: I/0 error, dev sda, sector 220473440 Quote Postby 1885 » 2015/12/18 14:11:58 TrevorH wrote:No bone, it's a dying End_request I/o Error Dev Sda Sector 0 Short self-test ran without throwing any errors.
I doubt that the Seagte support would be helpful but I will try to get SN12 for my ST32000644NS disks. The laptop passes the simple diagnostics, but when you really start to use it, problems show up. All they were doing were avoiding the load that caused the first error. here we are.You say it is probably dying. Blk_update_request Io Error
Why did Moody eat the school's sausages? Blk_update_request I/o Error Dev Sector Enter user and password and su to root. No Offline surface scan supported.
All Rights Reserved Privacy & Terms Arch Linux HomePackagesForumsWikiBugsAURDownload Index Rules Search Register Login You are not logged in.
The RAID10 with 4 disks (LVM proxmox) did snapshots to a 2TB back-up disk internally. I'll try your suggestion. Ran smartmontools test and got this result: === START OF INFORMATION SECTION === Model Family: Fujitsu MJA BH Device Model: FUJITSU MJA2250BH G2 Serial Number: K94PT972B7RS LU WWN Device Id: 5 Blk_update_request I/o Error Dev Fd0 Sector 0 Self-test supported.
ls -l /dev/sd* reveals that dev 08:50 is /dev/sdf however that drive doesnt exist so why would it be trying to access that drive? When I paste "blacklist floppy" it says "cklist floppy". It's free: ©2000-2016 nixCraft. The external HDD should be plugged in but not mounted, you can unmount the disk using the Disk Utility, and as Javier pointed out you can also use the Disk Utility
Update: As landroni suggested, I ran short and extended self-tests using gsmartcontrol. Extended self-test routine recommended polling time: ( 84) minutes. They diagnose the drive and the memory as well, both went good. Jan 06 03:39:12 titanium kernel: Buffer I/O error on device vda3, logical block 99647488 (From a Debian jessie guest, EXT4 directly on a VirtIO-based block device) When this happens, it affects
Several functions may not work. In the thread I linked above, someone recommended doing a "Complete drive test" with a certain Ultimate Boot CD. backing up disk with ddrescue; 2. SCT Feature Control supported.
Really hoping to get more light on this Adv Reply July 12th, 2014 #8 bensocket View Profile View Forum Posts Private Message First Cup of Ubuntu Join Date Jul 2014 more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed Replacing the Seagate drives looks to be the real solution. Usually that'd be so that some other driver will bind it instead, no matter which driver happens to get probed first.
Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the Fix attempts I wasn't clever enough to think of these myself, this is just a list of things that other folk with similar errors said worked for them.