Home > Ibm Error > Ibm Error Code 3426

Ibm Error Code 3426

Contents

Cause . . . . . : Error code 3426 was received while processing the recv() - length - TCP- function for the host server communications. If the connection was eventually successful, the intervention message will be attempted to be removed from the message queue, and process will continue. Setting this timeout to 0 does not disable the Port Timeout. Error Messages for *LAN PJL Device Descriptions contains the messages that are associated with remote output queue printing. More about the author

Could you please throw in some idea to resolve this. Cause . . . . . : A communications error occurred while receiving data from remote device at RMTLOCNAME our.tcp.adr.nbr. A good suggestion to start with is 5000K. If this is the case, disabling the Job Timeout by setting it to 0 should resolve the problem. http://www.scottklement.com/archives/ftpapi/201003/msg00016.html

A Connection With A Remote Socket Was Reset By That Socket.

If the QPFRADJ system value is set to 0 (No adjustment), then proceed to the next step to set the size of the *SPOOL pool. Examples include all dot matrix printers, all line printers, all ink jet printers, older laser printers (anything compatible with an HP LaserJet III or earlier), or laser or inkjet printers that we are using port no:8475 Error is : 1. You might want to ping IBM to see if they can address that side of things.

If you are using a DRDA client that supports Secure Sockets Layer (SSL), you must connect to port 448 on the server. Refer to the section Recommended Timeout Settings for IBM, HP and Lexmark Print Servers at the top of this document for information on changing the timeout settings. For information on configuration and limitations of *LAN 3812 PJL device descriptions, please refer to the following document: N1010134: Configuring a *LAN 3812 PJL Device Description The success of this connection Error Messages for *LAN PJL Device Descriptions CPD338D "An error occurred while receiving data" The LAN adapter timeout value has expired and the writer has ended.

If the messages are constant and contain the same TCP/IP address over and over again, then it is most likely that the writer is trying to print to a LAN attached Cpe3426 Error is mentioned below. This page was generated at 12:53 PM. The Job Timeout can typically be set through the control panel on the printer, or it can be set using the Lexmark MarkVision Utility.

If this problem is seen with these older adapters, attempt to reduce network congestion, replace the older MarkNet adapters with newer adapters that have the firmware upgrade, or do not use Many thanks to all who helped. Thanks everyone for your time. Lexmark MarkNet cards/print servers: Disable the End of Job Timeout or Job Timeout by setting it to 0.

Cpe3426

Command failed. https://groups.google.com/d/topic/comp.sys.ibm.as400.misc/RMKLrk8aB9k o Specifying a TCP/IP address with extra blanks after the IP address (such as '9.10.46.254 '). A Connection With A Remote Socket Was Reset By That Socket. It may appear that something is hung up or looping during that time. Econnreset It may require a TCP/IP communications trace to confirm that the Double SYN problem is occurring.

The joblog >would usually show >CPD338D from pgm QWPPJLDR >From module . . . . . . . . : WPPJLDR >From procedure . . . . . . : my review here Refer to section Recommended Timeout Settings for IBM, HP and Lexmark Print Servers at the top of this document for information on changing the timeout settings. Recovery . . . : See any previously listed message(s)to determine the cause of the error; if necessary, correct the error and issue the request again. like the AS400 was IPL'd and the partner Windows application didn't notice.

If the PING fails from the IBM i, but PING works from a Windows PC that is in the same subnet as the printer, then the default gateway or subnet mask We are working to getcurrent on PTF's.CPD338D Diagnostic 40 05/05/04 09:49:10 QWPPJLDRQSYS *STMT QWPPJLDR QSYS *STMTWPPJLDRSocket_RecvStatement . . . . . . . . . : 39WPPJLDRTo procedure . . . Ending or holding the writer will suppress the messages until the problem with the printer hardware has been resolved. click site If the printer supports HP PCL5e or HP PCL6, there is a good chance, but no guarantee, that it will support bi-directional PJL which is required for a *LAN 3812 PJL

This should typically be set to 9100 for most newer IBM Infoprint printers or 2501 for most older IBM Network Printer and Infoprint printers, 9100 for HP LaserJet with internal HP I tried to change LAN Manager Authentication level , but of no use. Note: If the printer is given a new IP address, then the *LAN 3812 PJL device description will need to be changed to specify that new IP address in the Remote

For more information, please refer to the following document: N1010213: Solution to Printer Writers Not Starting at IPL CPF6DF9 "Transformed data buffer too small" This can be caused from using an

This specific protocol violation is known as the Double SYN problem and was reported in the following IBM Informational APAR: IBM Informational APAR II12692, LIC-COMM-TCPIP AS/400 SENDS RST DUE TO INVALID When communicating with an AS/400 (iSeries), TI communicates with DPC as outlined in http://msdn.microsoft.com/en-us/library/gg163957.aspx. I am not getting any clue, what this Pre V2R2 encryption is :( Any help is greatly appreciated!!! Resolving the problem Note: This document was previously entitled *LAN PJL TCP/IP Device Description Configuration Settings.

Thanks again. 2. www.code400.com Comment Post Cancel Red Analyst Join Date: Mar 2005 Posts: 392 #3 February 19th, 2007, 12:48 PM Re: Has anyone come accross this error ( 3426:A) Not sure if this If the Printer Error Message parameter in the Device Description for the writer was set to *INQ, then the intervention will require an operator input to retry or to cancel the http://upintheaether.com/ibm-error/ibm-error-code-173.php The error code is 3426.

We were > sending some complex print jobs, and the 90-second timeout would hit > while it was being processed. This is what I found after doing some research. o If CPD337C is received when printing to an IBM Infoprint 1100, 1200, 1300 or 1400 Series printer or a Lexmark Optra printer, it could indicate that the Job Timeout in PJL allows for two-way communication with the printer when attached to the LAN using a print server that also supports bidirectional PJL. *LAN 3812 PJL device descriptions have become a popular

The Lexmark MarkVision Utility can be downloaded from Lexmark's Web site, www.lexmark.com/. We could have a case where a partial page is sent to the printer's buffer while complex transforming is taking place during which this timer expires and, therefore, ejects an incomplete