Home > Hp Psc > Hp Psc 1350 Ink Cartridge Error

Hp Psc 1350 Ink Cartridge Error

Contents

Reconnect the power cord to the rear of the product. I have a MacBook Pro. caution: You must disconnect the power cord to move parts by hand without the risk of an electrical shock. If the test page does not print, continue with the next solution. http://upintheaether.com/hp-psc/hp-psc-1350-cartridge-error.php

Solutions Solution one: Wait for the All-in-One to complete the job The product is processing a copying, scanning, printing, or photo or maintenance job. On some models, the language and country/region settings also reset. Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the job. Maybe I should try cleaning the contacts, unless you have any ideas.Thanks,IR12 Reply 0 0 Bob_Headrick Provost Posts: 27,159 Member Since: ‎11-17-2008 Message 7 of 13 (14,917 Views) Report Inappropriate Content

Hp Psc 1350 Troubleshooting

Continue with the steps below - you must perform the steps on both cartridges. Wait until the On/Resume button () is steady. Reconnect the USB cable to the rear of the product. The carriage is stuck and does not move.

Recently I have been having issues with my HP printer - whenever I try to print, a 'print cartridge error' is displayed. The tray contains more than one type of paper. note: An E might also appear in the Copies display. Hp Psc 1350 Manual If the product does not complete the cartridge alignment, it will print an alignment page every time you turn on the product.

Removing and reinstalling the cartridge may help. Clean the print cartridge contacts. Figure : Reinsert the cartridge Firmly push the cartridge in until it snaps into place. https://h30434.www3.hp.com/t5/Inkjet-Printing/Sudden-Print-Cartridge-Error-For-PSC-1315-Unsolvable/td-p/277223 There is a small possibility that it is a problem with the printer, but the cartridges are the most likely cause.The support number is:1-(800)-HP INVENT1-(800)-474-6836Thank you I was an HP employee.Kudos

Step one: Make sure that the carriage can move freely Press the On/Resume button () to turn on the product. Hp Psc 1210 Troubleshooting Step one: Make sure that the carriage can move freely Press the On/Resume button () to turn on the product. Turn the printer off for a minute.Step 5Turn the HP printer on. Press and release the Copies button.

Hp Psc 1315 Check Printer Cartridge Error

Then slide the cartridge out of the carriage. If the alignment page does not print automatically, follow these steps to print one manually: If the product is off, press the On/Resume button () to turn on the product. Hp Psc 1350 Troubleshooting Step two: Test the connection Press the appropriate button(s) on the product again to perform the intended task. Hp Psc 1210 Check Print Cartridge Error See here for a study of cartridge reliability of HP original cartridges comapred to refill/reman.Cleaning the cartridge and printer contacts as show in this post may help.Sherman/Clayton would not suggest a

Follow these steps to perform a partial reset of the product. http://upintheaether.com/hp-psc/hp-psc-1350-print-cartridge-error.php If the issue persists, continue to the next solution. The printer will not print. Step one: Clean the electrical contacts on the cartridges and inside the product Gather the following materials: Dry foam rubber swabs, a lint-free cloth, or any soft material that will not Hp Psc 1350 Error Code E

note: If the carriage does not move into the access area, turn the product off and then on again. Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. Close the cartridge access door by pressing firmly on the door until it snaps into place. check over here If these steps resolved the issue, you do not need to continue troubleshooting.

I don't want to buy new cartridges and then not use them. Hp Psc 1410 Check Print Cartridge Flashing If the issue persists, continue to the next solution. If the product is unresponsive for more than 60 seconds, continue to the next solution.

Figure : Remove the rear access door Gently remove any jammed paper or bits of torn paper from the rollers inside the product.

Solution three: Check cartridge compatibility Visit HP SureSupply to check ink or toner cartridge compatibility, or purchase replacement cartridges. Try the intended task again. Press down on the end of the problem cartridge to snap it out of the carriage. How To Reset Hp Psc 1410 Printer Open the cartridge access door.

I assume that the next suggestion is to replace it with HP NEW #57 but what would Sherman & Clayton say? Reply 1 1 feroneil Honor Student Posts: 2 Member Since: Figure : Snap the cartridge into place Repeat these steps to insert the other cartridge into its designated slot. Figure : Open the cartridge access door Hold the cartridge on its sides, and then slide the cartridge forward into its slot at a slightly upward angle. http://upintheaether.com/hp-psc/hp-psc-1350-printer-cartridge-error.php Securely reconnect the USB cable to the rear of the computer.

An obstruction is blocking the paper path. Blinking Lights on the HP PSC 1200, 1310, 1340, and 1350 All-in-One Printer Series Blinking Lights The following sections describe all combinations of blinking (flashing) lights displayed on the product control Follow these steps to perform a partial reset of the product. If the message on the computer does not identify a particular cartridge (it says only Print cartridge error), follow the steps below to determine which cartridge is causing the problem.

Open the cartridge access door. Just goes back to blinking. If these steps resolved the issue, you do not need to continue troubleshooting. Figure : Open the cartridge access door Remove the black cartridge by pressing lightly on the top of the cartridge to release it from its slot.

Remove the cartridge and place it on a piece of paper with the nozzle plate facing up. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Make sure that the stack of paper is no higher than the top of the paper width guide. If the issue persists, continue to the next solution.

If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. If the product uses a power module with a detachable power cord, disconnect the cord from the power module. Press and hold the Cancel button (). Plug the power cord back into the wall outlet.

The carriage moves to the center of the product. Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Figure : The rollers in the rear access door Gently push the pins on the right end of the rear access door into the holes on the right side of the Use only one type of paper at a time.

Remove the cartridge.Step 2Remove the cartridge and use a clean, lint-free, dry cloth to gently wipe the contacts.Step 3Wipe from the top of the contact to the bottom.