Home > Hp Psc > Hp Psc 1350 Error Blinking Lights

Hp Psc 1350 Error Blinking Lights

My toddler just broke ours and it doesn't look like the parts are available from hp anymore.Does anyone know if there's another acceptable replacement part or another place to get one To reinsert, hold the cartridge by its sides, and then slide the cartridge forward into its slot at a slightly upward angle. If the product does not complete the cartridge alignment, it will print an alignment page every time you turn it on. Try the intended task again. http://upintheaether.com/hp-psc/hp-1350-error-lights.php

Figure : Gently remove the jammed paper caution: If the paper tears, remove the torn pieces from the rollers and wheels. Figure : Clean the print cartridge contacts Clean the contacts in the print carriage, inside the printer. Try the task again to see if this solution resolved the issue. Figure 67: Open the cartridge access door Remove the black cartridge by pressing lightly on the top of the cartridge to release it from its slot. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c00095908

So I'll see you in 5 years.BK by BruceKal on Feb 23, 2011 at 4:58pm Add comment Please sign in to comment 0 I have refilled the cartidge myself twice and Open the cartridge access door. The reset is now complete.

This might happen iif we are not installing the orignal and genuine catridges and there is a chance of ink gettng leaked onto the printer. Figure 30: Open the cartridge access door Without turning off the product, disconnect the power cord from the rear of the product. Step one: Change the settings Select the method for resolving the issue, and then follow the steps in the order given. If the issue persists, try a different electrical outlet.

If you do not, in spite of ink being in the cartridge it is defective. When only the Power light () is flashing, release both buttons. by Bert on Mar 19, 2009 at 8:13pm Add comment Please sign in to comment 0 Printer was working fine, next print I got the "E" and "check print cartridge". If these steps resolved the issue, you do not need to continue troubleshooting.

Figure : Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner. Can anyone help? If you press the On/Resume button () again during this time, you might turn the product off. If after trying the task, a blinking light or combination of blinking lights displays on the product control panel, find the pattern you are experiencing in this document, and then follow

If the issue persists, continue to the next solution. If these steps resolved the issue, you do not need to continue troubleshooting. Make sure that the paper is free of rips, dust, wrinkles, and curled or bent edges, and that all the paper in the stack is the same size and type. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.

When only the On/Resume button () is blinking, release both buttons. http://upintheaether.com/hp-psc/hp-psc-1350-error-e.php Press the Power button () to turn on the product. The Size is: window opens. If the self-test report does not print, skip to the next step.

Plug the power cord directly into an electrical outlet. Check out the other info also. Unplug the power cord from the electrical outlet. check over here If the product does not turn off, continue to the next solution.

If not, then kudos to whomever you were referring to. =^D by unknown on Jul 9, 2008 at 3:26pm Add comment Please sign in to comment 0 My On/Resume light does May 12, 2014 | HP PSC 1350 All-In-One Thermal Printer 0 Answers how do I reset my hp printer as I have lost my manual mp printer keeps displaying that my A flashlight will be helpful.If the paper will still not feed the jam removal may have damaged the mechanism.

Then slide the cartridge out of the carriage.

Plug the alternate power cord into the wall outlet. Do not overload the tray with paper. The carriage moves to the center of the product. When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time.

Figure : Insert the paper into the paper tray Slide the paper width guide inward until it is snug (but not tight) against the paper. Plug it back in and reconnect it to the computer.9. The alignment page prints. http://upintheaether.com/hp-psc/hp-psc-1350-error.php Press firmly on the overlay to ensure proper installation of the overlay adhesive or pins.

On some models, the language and country/region settings also reset. If the test page does not print, continue with the next solution. Torn pieces of paper from a previous jam are stuck in the product. Step two: Print a self-test report Follow these steps to print a self-test report.

Went to desktop control panel and looked up printer it said paper jam so I deleted the document out of the print que. On some models, language and country/region settings also reset. Figure : Load the alignment page Close the scanner lid while holding the alignment page in place. Click OK to accept the settings.

You would think hp's Quality Control Department would devise a fix for this. Close the cartridge access door. Do I take it that this printer will not print on glossy photo paper? Remove any loose paper or obstructions found.

From the Size: drop-down list, click Custom. Z7_3054ICK0KGTE30AQO5O3KA3015 hp-online-communities-portlet Actions ${title} Loading... See your browser's documentation for specific instructions. {} Z7_3054ICK0KGTE30AQO5O3KA30U5 hp-support-head-portlet Actions ${title} Loading... Press the Power button () to turn on the product.

If the issue persists, continue to the next solution. The Print window opens. any ideas thx maddchess Apr 07, 2009 i also found that the on/off button and thcancel gave some effect but didnt seem to fix it hmm any help appriciatedthx i also If these steps resolved the issue, you do not need to continue troubleshooting.