Home > Hp Psc > Hp Psc 1315 Cartridge Error

Hp Psc 1315 Cartridge Error

Contents

Follow these steps to perform a partial reset of the product. This video shows how to print a test page Click here to see this video in full screen on YouTube. If the product is unresponsive for more than 60 seconds, continue to the next solution. WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... his comment is here

Do not overload the tray with paper. Issue: The Check Paper light blinks In this error condition, the following blinking lights pattern displays on the control panel: On/Resume light: On Check Paper light: Blinking Check Print Cartridge light: Issue: The On/Resume light blinks for 3 seconds and then remains on, and the Black Start Copy and Color Start Copy lights blink In this normal condition, the On/Resume light () Put the ink back in it one at a time and try to print a test page.

Hp Psc 1350 Check Print Cartridge

caution: You must disconnect the power cord to move parts by hand without the risk of an electrical shock. Disconnect the product cord from any power strip or surge suppressor, and then plug it directly into a three-prong wall outlet. Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the current job. Both cartridges are about half full (my computer can read the levels before I try to print).

Connect the USB cable to continue the print job. Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus! Solutions Solution one: Wait for the All-in-One to complete the job The product is processing a copying, scanning, printing, or photo or maintenance job. Hp Psc 1210 Troubleshooting Follow these steps to plug your product directly into a wall outlet.

Load plain white paper in the paper tray. A sequence of buttons on the control panel must now be pressed in the order presented. If the issue persists, continue to the next solution. his explanation Discussion topics include choosing a processor, installing hard drives, adding RAM, upgrading video cards, sound cards, DVD drives, Blu-ray drives, PSU, and much more.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General discussion Error after

Thank you! Register · Log In HP Support Forum Home > Printers > Inkjet > hp psc1315 suddenly gives me a "Check Print Cartridge" error... How To Reset Hp Psc 1410 Printer Scroll to the bottom of the page, and then make sure the country/region location is correct. Use bottled or filtered water if distilled water is not available. Follow the on-screen instructions to order new cartridges or check cartridge compatibility with your printer.

Hp Psc 1350 Troubleshooting

The carriage moves to the center of the product. On some models, the language and country/region settings also reset. Hp Psc 1350 Check Print Cartridge Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Hp Psc 1410 Check Print Cartridge Flashing If the product does not turn on automatically, press the On/Resume button () to turn the product back on.

Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Never pull jammed paper from the front of the this content note: If the carriage does not move into the access area, turn the product off and then on again. You can only upload a photo (png, jpg, jpeg) or a video (3gp, 3gpp, mp4, mov, avi, mpg, mpeg, rm). note: An E might also appear in the Copies display. Hp Psc 1210 Check Print Cartridge Error

With the product turned on, disconnect the power cord from the rear of the product. Step two: Print a self-test report Follow these steps to print a self-test report. note: If the carriage does not move into the access area, turn the product off and then on again. weblink Close the cartridge access door.

READ MORE © CBS Interactive Inc.  /  All Rights Reserved. Hp Psc 1350 Error Code E Do not leave a cartridge outside the product for more than 30 minutes. However, since that event, when I change cartridges, the printer does not automatically print a test pattern for realignment.

The reset is now complete.

Step two: Print a self-test report Follow these steps to print a self-test report. Figure : Disconnect the power cord Unplug the power cord from the wall outlet. To do a hard reset:1. Hp Psc 1350 Manual When the Check Paper and Check Print Cartridge lights begin to blink simultaneously, release both the Cancel button () and the On/Resume button ().

The sequence must be completed within 10 seconds. If the product does not automatically turn on, press the Power button Open the cover and reinsert the print cartridges Close the cover. Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Always try to pull jammed paper from the rear check over here Step one: Install the cartridges Press the On/Resume button () to turn on the product.

Solution three: Match the paper to the paper settings Follow these steps to make sure that the paper loaded into the product matches the paper size and type settings in the Open the cartridge access door. Blinking Lights on the HP PSC 1200, 1310, 1340, and 1350 All-in-One Printer Series Blinking Lights The following sections describe all combinations of blinking (flashing) lights displayed on the product control note: You might need a flashlight to illuminate areas for proper viewing.

Doing so can cause bad electrical connections, clogged ink nozzles, or poor print quality. Make sure that the stack of paper is no higher than the top of the paper width guide. Use both hands to pull any whole sheets of paper to avoid tearing them. Torn pieces of paper from a previous jam are stuck in the product.

Figure : Remove the rear access door Gently remove any jammed paper or bits of torn paper from the rollers inside the product. The color cartridge belongs in the slot on the left. If these steps resolved the issue, you do not need to continue troubleshooting. note: If the carriage does not move into the access area, turn the product off and then on again.

Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch. Check the control panel to make sure that the lights are no longer blinking.