Hp Psc 1310 Print Cartridge Error
If the product has not been set up before, follow these steps to ensure correct installation of the front panel overlay. Sowrav D. Issue: The On/Resume light blinks rapidly for 20 seconds, and then remains on In this error condition, the following blinking lights pattern displays on the control panel: On/Resume light: Blinks rapidly NOTE: Try to clean the contacts quickly enough that the cartridge is not outside of the printer for more than 30 minutes. his comment is here
Figure : Disconnect the power cord Remove the rear access door. Check to see if the power module has an LED. If the On/Resume light does not blink, you cannot tell which cartridge is the problem cartridge. note: You might need a flashlight to illuminate areas for proper viewing. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00461967
Hp 1350 Printer Check Print Cartridge Error
Open the cartridge access door. The tray is too full. Figure 5: Replacing the cartridge The black or photo cartridge goes on the right. Use bottled or filtered water if distilled water is not available.Clean cotton swabs or any soft, lint-free material that will not stick to the cartridges (coffee filters work well).Remove the cartridge
If the issue persists, continue to the next solution. Press and release the Cancel button () again. I took out the black ink cartridge, and I was able to print out some ink refill page the program popped up cause of the missing cartridge. Hp Psc 1350 Error Code E I remember thattrying different cartridges didn't get rid of the error.
Step two: Reinstall the cartridges To reinsert, hold the cartridge by its sides, and then slide the cartridge forward into its slot at a slightly upward angle. Hp Psc 1315 Check Printer Cartridge Error Resolved Question: My hp psc 1310 throws up a "Print Cartridge Error" report. With the power on, disconnect the power cord from the rear of the product. He simply convinced the gremlins to leave and infest some other printer.Seriously, I can manually create an alignment page but scanning it produces no change in quality.
It might take several tries to complete the sequence within ten seconds. Hp Psc 1210 Troubleshooting Follow these steps to perform a partial reset of the product. Load plain white paper in the paper tray. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.
Hp Psc 1315 Check Printer Cartridge Error
This will cause these types of errors as well. this content Insert the paper into the paper tray print side down until it stops. Bob Headrick, HP ExpertI am not an employee of HP, I am a volunteer posting here on my own time.If your problem is solved please click the "Accept as Solution" button------------VIf To avoid bending the paper, make sure that you do not push the paper in too far, or push too hard. Hp Psc 1350 Manual
Issue: The On/Resume light blinks for 3 seconds and then remains on, and the Black Start Copy and Color Start Copy lights blink In this normal condition, the On/Resume light () Figure : Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner. Figure : Load the alignment page Close the scanner lid, The carriage moves to the center of the product. weblink Step one: Replace defective cartridge This video shows how to replace the ink cartridges Click here to see this video in full screen on YouTube.
These can damage the cartridge or the product. Hp 1350 Printer Won't Feed Paper Doing so can cause bad electrical connections, clogged ink nozzles, or poor print quality. While holding the Cancel button (), press and hold the On/Resume button ().
On some models, the language and country/region settings also reset.
Solution three: Match the paper to the paper settings Follow these steps to make sure that the paper loaded into the product matches the paper size and type settings in the I 'ordered' a print job and suddenly had an error, red light, on "check cartridge". Figure : Gently remove the jammed paper caution: Use a flashlight to thoroughly check the rollers and wheels for torn pieces of paper that might remain inside the product. Hp Psc 1350 Troubleshooting Followed HP trouble shooting guide.
If these steps resolved the issue, you do not need to continue troubleshooting. Any one have a suggestion? Plug the power cord back into the wall outlet. http://upintheaether.com/hp-psc/hp-1310-check-print-cartridge-error.php Follow the on-screen instructions to order new cartridges or check cartridge compatibility with your printer.
Only add paper to the tray when the product is not printing. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Error still exists.HP popup on Windows 7 screen shows new color cartridge empty...black cartridge half full.I know this is a while back but just wondering if you got it resolved?ThanksCiara I Disconnect the USB cable from the rear of the product.
Hi,Welcome to Just Answer ,My name isXXXXX will try to help you..The problem you are describing is caused by defective print head and you may have to replace the print head, caution: You must disconnect the power cord to move parts by hand without the risk of an electrical shock. If the product operates normally, allow the product to complete the job. Make sure that the paper is free of rips, dust, wrinkles, and curled or bent edges, and that all the paper in the stack is the same size and type.
Issue: The On/Resume light blinks In this normal condition, the following blinking lights pattern displays on the control panel: On/Resume light: Blinking Check Paper light: Off Check Print Cartridge light: Off Twitter: @Ciara_B_HP Reply 0 0 millibob Top Student Posts: 3 Member Since: 09-04-2013 Message 5 of 8 (4,490 Views) Report Inappropriate Content Re: hp psc1315 suddenly gives me a "Check Print Solution three: Press the On/Resume button more slowly The product might not respond if you press the On/Resume button () too quickly. Press the On/Resume button () to turn on the product.
Make sure that the carriage can move freely across the width of the product by gently pushing the carriage to the left and then to the right. READ MORE © CBS Interactive Inc. / All Rights Reserved. Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. You should also inspect the carrier itself.
Press and hold the Cancel button (), and then press the Start Copy Color button. Press the On/Resume button () to turn on the product. Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP Printers - After Windows 10 If these steps resolved the issue, you do not need to continue troubleshooting.