Home > Hp Psc > Hp Psc 1300 Series Print Cartridge Error

Hp Psc 1300 Series Print Cartridge Error

Contents

Issue: The On/Resume, Check Paper, and Check Print Cartridge lights blink In this error condition, the following blinking lights pattern displays on the control panel: On/Resume light: Blinking Check Paper light: When I hit the On button, the display goes back to normal.The printer is stopping during print jobs and giving an error on screen that says Check the print cartridges. Press the On/Resume button () to turn on the product. With the power on, disconnect the power cord from the rear of the product. weblink

Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! If the issue persists, continue to the next solution. I took the 1350 case off and can see that it attaches to a clip on the right side. As for either the scanner or processor - there isn't much you can do about these on this machine. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00461967

Hp 1350 Printer Check Print Cartridge Error

The product aligns the cartridges. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking. The sequence must be completed within ten seconds. by unknown on Aug 28, 2007 at 6:34pm Add comment Please sign in to comment 0 All lights flashing typically means a fatal error.

If machine still gives you problems after a driver uninstall and reinstall, download the the latest driver version, hope you have a high speed Internet connection. And then I pulled the paper out of it. HP Support Forums Join in the conversation. Figure : The door pins Step three: Clear the paper jam from the front of the All-in-One If you cannot remove the paper jam from the rear of the product, follow

Figure : Lift the scanner lid Place the alignment page face down on the scanner glass in the lower-left corner. Hp Psc 1350 Manual If the issue persists, continue to the next solution. The sequence must be completed within ten seconds. http://support.hp.com/us-en/document/c00095908 If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.

Note: This will cause printing to be a bit slower for you as using disk space of ram is slower than conventional memory. HOW DO I GET READ OF THE STREAK. Dip a swab in the clean water, then squeeze it to remove most of the moisture. If the alignment page does not print automatically, follow these steps to print one manually: If the product is off, press the On/Resume button () to turn on the product.

Hp Psc 1350 Manual

If these steps resolved the issue, you do not need to continue troubleshooting. https://forums.techguy.org/threads/hp-psc-1350-all-in-one-wont-work.739896/ I bought a new black 56 cartridge and installed it but I still get the flashing red button. Hp 1350 Printer Check Print Cartridge Error If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Hp Psc 1350 Troubleshooting I inserted my memory card from digital camera into the slot in front of printer...and the dialog box appeared on my computer screen..tells what program i want to see my pics...so

Disconnect the product cord from any power strip or surge suppressor, and then plug it directly into a three-prong wall outlet. have a peek at these guys Do not print on paper with paper clips or staples attached. won't print but [Edited] Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎06-14-2011 06:58 AM - last edited on ‎04-18-2016 by Ryobic on Jul 16, 2008 at 12:21am Add comment Please sign in to comment 0 Whenever we lose power in our area, the printer goes berserk. Hp Psc 1350 Printer

Other than "Don't turn the printer off", does anyone have any suggestions? If after trying the task, a blinking light or combination of blinking lights displays on the product control panel, find the pattern you are experiencing in this document, and then follow Solutions Solution one: Close the cartridge access door Make sure that the cartridge access door is completely closed. check over here The system returned: (22) Invalid argument The remote host or network may be down.

Press the On/Resume button () to turn on the product. It is also no longer showing up as being connected to my computer. It is not hooked up to the computer.

Reconnect the USB cable to the rear of the product.

Open the cartridge access door. show more Recently I have been having issues with my HP printer - whenever I try to print, a 'print cartridge error' is displayed. Modern printer software uses memory like eating candy. Step three: Replace the USB cable Securely connect an alternate USB cable to the rear of the product.

Figure 3: Removing the problem cartridge If there is tape on the cartridge, remove it. Reconnect the USB cable to the rear of the product. note: If the alignment page fails to print, repeat the button-press sequence in this step. this content Figure : Remove the rear access door Press in the tab Pull out the door Lightly dampen a clean, lint-free cloth with bottled or distilled water, and then squeeze any excess

If the power module does not have an LED, continue to the next step. The product prints a self-test report. Do not use a power strip or surge protector. Printer printed test sheet but would not print document.

I have tried alot of things and they are not working. Load plain, white paper into the paper tray. note: If you have already installed the front panel overlay, proceed to the next solution. note: An E might also appear in the Copies display.

Press and release the Paper Type button. Like others on this page I have recently encountered black print cartridge problems. Click here to skip to Step 3 below - you only have to perform the steps on the problem cartridge . Try the intended task again.

With the product turned on, disconnect the power cord from the rear of the product.