Home > Hp Psc > Hp Psc 1210xi Check Print Cartridge Error

Hp Psc 1210xi Check Print Cartridge Error

Contents

note: If the alignment page fails to print, repeat the button-press sequence in this step. Solution two: Check the connection between the All-in-One and the computer Follow these steps to make sure that the USB cable is securely connected to the product and the computer. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. Dip a clean foam rubber swab or lint-free cloth into distilled water, and then squeeze any excess water from it. his comment is here

Step two: Align the cartridges Follow these steps to align the cartridges. Place it in its slot at a slight angle, and then press up and forward until the cartridge snaps into position.Figure 5: Replacing the cartridgeThe black or photo cartridge goes on The printer should automatically power back up. Connect the alternate power cord to the rear of the product. http://support.hp.com/us-en/document/c00094661

Hp Psc 1210 Troubleshooting

You might look atthe "Check Print Cartridge light is blinking" about half way downin the document link below:http://support.hp.com/us-en/document/c01578337If those don't work, you might tryleaving the printer in turned on status, then Try the intended task again. note: Try to clean the contacts quickly enough that the cartridge is not outside of the printer for more than 30 minutes. If these steps resolved the issue, you do not need to continue troubleshooting.

Please help! Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. Any other suggestions? Hp Psc 1410 Check Print Cartridge Flashing Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Never pull jammed paper from the front of the

Press the On/Resume button () to turn off the product. Open the cartridge access door. The carriage moves to the center of the product. Would LOVE to find a solution, as I can't print anything.B.

Also worked in The US Army as A Network Switching Systems Operator/Controller 19897260 Type Your Printers Question Here... How To Reset Hp Psc 1410 Printer Solution two: Plug the All-in-One directly into a wall outlet The power source your product is plugged into might not function properly. Step one: Replace defective cartridge This video shows how to replace the ink cartridges Click here to see this video in full screen on YouTube. If these steps resolved the issue, you do not need to continue troubleshooting.

Hp Psc 1350 Check Print Cartridge

Modify your browser's settings to allow Javascript to execute. Removing and reseating the cartridges might help. Hp Psc 1210 Troubleshooting Clean the print cartridge contacts. Hp Psc 1315 Check Printer Cartridge Error If you cannot cancel the task, press and hold the On/Resume button () for three seconds to turn off the product.

When only the On/Resume button () is blinking, release both buttons. http://upintheaether.com/hp-psc/hp-psc-1410v-check-print-cartridge-error.php Step two: Reinstall the cartridges To reinsert, hold the cartridge by its sides, and then slide the cartridge forward into its slot at a slightly upward angle. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Hp Psc 1350 Troubleshooting

Reconnect the power cord to the rear of the product. Torn pieces of paper from a previous jam are stuck in the product. Try the intended task again. weblink Press the On/Resume button () to turn on the product.

Learn more You're viewing YouTube in German. Hp Psc 1210 Reset When only the On/Resume button () is blinking, release both buttons. If these steps resolved the issue, and the test page prints, there is no need to continue troubleshooting.

Open the scanner lid.

Wait until the On/Resume button () is steady. Press the On/Resume button () once slowly to turn on the product. Solution two: Cancel and then retry the task Follow these steps to cancel and then retry the current task. Reset Hp Psc 1210 All In One Press firmly on the overlay to ensure proper installation of the overlay adhesive or pins.

A sequence of buttons on the control panel must now be pressed in the order presented. To start with.. An alignment page prints automatically. http://upintheaether.com/hp-psc/hp-psc-1210-error-check-print-cartridge.php Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar.

The product aligns the cartridges. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking. Figure : Remove the paper backing from the front panel overlay Lift the scanner lid. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. Solution two: Cancel and then retry the task Follow these steps to cancel and then retry the current task.

Figure : Removing the tape Replace the cartridge. The alignment page prints. And then try to print.. Use both hands to pull any whole sheets of paper to avoid tearing them.

Avoid touching the nozzles.Figure 6: Clean the print cartridge contactsClean the contacts in the print carriage, inside the printer. When the Check Paper and Check Print Cartridge lights begin to blink simultaneously, release both the Cancel button () and the On/Resume button (). The following blinking lights pattern displays on the control panel: On/Resume light: Blinks fast for 3 seconds and then stays on Check Paper light: Off Check Print Cartridge light: Off Black This video shows how to print a test page Click here to see this video in full screen on YouTube.

If the issue persists, continue to the next step. Figure : Gently remove the jammed paper caution: Use a flashlight to thoroughly check the rollers and wheels for torn pieces of paper that might remain inside the product. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. Go to HP Customer Support - Software and Driver Downloads.

The carriage moves to the center of the product. Figure : Snap the cartridge into place Repeat these steps to clean the contacts on the other cartridge and in the other side of the carriage. Dustin and 3 other Printers Specialists are ready to help you Ask your own question now Share this conversation Related Printers Questions Question Date Submitted If my GPO is turned on Follow these steps to clean the paper feed rollers.

The presence of an E, however, does not affect the meaning of the blinking lights, and can be disregarded for troubleshooting purposes. Solution two: Install the cartridges Follow these steps to install the cartridges in the product. Had new cartridges handy and replaced both when this blinking began, but the light will not stop blinking, and will not print. HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading...