Home > Hp Psc > Hp Psc 1210 Print Cartridge Error

Hp Psc 1210 Print Cartridge Error

Contents

You can try removing the cartridges, and shaking them very very vigorously, as that may help.. Press and release the Copies button. Figure : Open the cartridge access door Hold the cartridge on its sides, and then slide the cartridge forward into its slot at a slightly upward angle. Figure : Open the cartridge access door Remove the new cartridge from its packaging, and then use the pull tab to remove the protective tape from the nozzles. Figure : http://upintheaether.com/hp-psc/hp-psc-1210-check-print-cartridge-error.php

Figure : Secure the USB cable note: Make sure that the USB cable is connected correctly. Close the cartridge access door. Then, turn the printer off.. When the On/Resume light is steady, the reset is complete." Tip: The only certain way to verify operation of the cartridges is to test them in known working printer. click to read more

Hp Psc 1350 Check Print Cartridge

If the issue persists, continue to the next solution. Press in the tab on the left side of the door, and then pull the door away from the product to remove it. Follow these steps to clear any jammed paper. This is annoying as hell.

Try the intended task again. caution: Do not clean the ink nozzles on the bottom of the cartridge Figure : The copper-colored electrical contacts on the cartridge Allow the contacts to dry for about 10 minutes. If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1210 Troubleshooting Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.

Reconnect the power cord to the rear of the product. Figure : Disconnect the power cord Wait 15 seconds. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Then slide the cartridge out of the carriage.

Figure : Disconnect the power cord Remove the rear access door. How To Reset Hp Psc 1410 Printer Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. If these steps resolved the issue, you do not need to continue troubleshooting. If the product does not scan, follow the same steps and try a different wall outlet.

Hp Psc 1350 Troubleshooting

note: If the carriage does not move into the access area, turn the product off and then on again. http://support.hp.com/us-en/document/c00095908 Solution two: Load paper Follow these steps to load letter or A4 paper into the product. Hp Psc 1350 Check Print Cartridge Insert the cartridges again. Hp Psc 1315 Check Printer Cartridge Error If the issue persists, continue to the next solution.

To avoid bending the paper, make sure that you do not push the paper in too far, or push too hard. http://upintheaether.com/hp-psc/hp-psc-1210-error-check-print-cartridge.php Avoid touching the nozzles.Figure 6: Clean the print cartridge contactsClean the contacts in the print carriage, inside the printer. While holding the Cancel button (), press and hold the On/Resume button (). Over time, the ink inside gums up.. Hp Psc 1410 Check Print Cartridge Flashing

The tray contains more than one type of paper. Submitted: 4 years ago. Step one: Perform a power reset Press the On/Resume button () to turn on the product. weblink Contact HP to replace the power cord.

Press and hold the Cancel button (), and then press the Start Copy Color button. Hp Psc 1350 Error Code E If these steps resolved the issue, you do not need to continue troubleshooting. The ink can dry and clog the nozzles if the cartridge is outside of the printer for too long.Unplug the printer.Dip a swab in the clean water, then squeeze it to

Try the intended task again.

Step two: Align the cartridges Follow these steps to align the cartridges. After 60 seconds, plug the cord directly into a wall outlet (not a surge protector or battery backup as they can cause the printer to lose basic functionality over time).5. Figure : The location of the carriage contacts Figure : The gold-colored electrical contacts inside the carriage Wait about ten minutes to allow the electrical contacts to dry, or use a Hp Psc 1350 Manual If the issue persists, continue to the next step.

Plug the alternate power cord into the wall outlet. If the product does not complete the cartridge alignment, it will print an alignment page every time you turn it on. Plug the power cord back into the wall outlet. check over here Ink still fresh when I wiped bottom of cart.

Step one: Make sure that the carriage can move freely Press the On/Resume button () to turn on the product. If the carriage is stuck in the middle of the product, move the carriage to the right side of the product. Use a second moistened foam rubber swab or lint-free cloth to clean the gold-colored electrical contacts in the carriage, inside the product.