Home > Hp Psc > Hp Psc 1210 Error

Hp Psc 1210 Error

Contents

Right-click this link, Product Support Home Page, and then click Open in New Window. Topic Tools #1 August 31st, 2008, 08:00 PM morby Senior Member Join Date: Dec 2005 O/S: Windows Vista Location: UK Posts: 142 HP psc 1210 all-in-one Printer Error If the product does not turn on with the alternate power cord, continue to the next solution. Figure : Remove the rear access door Press in the tab Pull out the door Gently remove any jammed paper or bits of torn paper from the rollers inside the product. weblink

Connect the alternate power cord to the rear of the product. Compare the paper size and type settings on the Paper/Quality tab to the paper loaded in the paper tray. When only the On/Resume button () is blinking, release both buttons. Step two: Print a self-test report Follow these steps to print a self-test report. see it here

Hp Psc 1210 Check Print Cartridge Error

Load plain, white paper into the paper tray. If the issue persists, continue to the next solution. Close the cartridge access door. HP Printer Support 75,606 views 13:06 The Dirty Little Secret Of Inkjet Printers - Duration: 1:38.

Step three: Align the cartridges Follow these steps to align the cartridges. Check the lights on the control panel to make sure that they are no longer blinking. This video shows how to clear a carriage jam Click here to see this video in full screen on YouTube. Hp Psc 1350 Troubleshooting Wait until the On/Resume button () is steady.

If the power module does not have an LED, continue to the next step. The check printer cartridge light is blinking. If these steps resolved the issue, and the self-test report prints, there is no need to continue troubleshooting. navigate to this website Try the intended task again.

Sign in to report inappropriate content. How To Reset Hp Psc 1410 Printer Step three: Replace the USB cable Securely connect an alternate USB cable to the rear of the product. Figure : Open the cartridge access door Press lightly on the top of the cartridge that you are removing to release it from its slot. If you have cleaned the cartridge and carriage electrical contacts with a cotton swab and alcohol, and are absolutely sure that the cartridges you've tried are good, do what HP calls

Hp Psc 1350 Check Print Cartridge

Wait until the On/Resume button () is steady. On some models, the language and country/region settings also reset. Hp Psc 1210 Check Print Cartridge Error Z7_M0I02JG0KONJ30ACBBF8MM1084 hp-hero-support-search Actions ${title} Loading... Hp Psc 1210 Troubleshooting Figure : Load the alignment page Close the scanner lid, and then press the Scan button on the control panel.

These can damage the cartridge or the product. have a peek at these guys Solution three: Clear any jammed paper Jammed paper can cause the carriage to stall. Figure : Secure the USB cable note: Make sure that the USB cable is connected correctly. If the issue persists, continue to the next solution. Hp Psc 1315 Check Printer Cartridge Error

If the product does not complete the cartridge alignment, it will print an alignment page every time you turn on the product. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  check over here If the product has not been set up before, follow these steps to ensure correct installation of the front panel overlay.

Only add paper to the tray when the product is not printing. Hp Psc 1410 Check Print Cartridge Flashing Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking. Solution three: Install the HP software You must download and then install the HP product software in order for your computer to detect the product.

If the issue persists, continue to the next solution.

Figure : The door pins Reconnect the power cord to the rear of the product. If the power module has an LED, check to see if the LED lights up. HP Printer Support 93,281 views 14:46 Loading more suggestions... Hp Psc 1350 Manual http://h10025.www1.hp.com/ewfrf/wc/g...name=c00094661 This link is to the exact problem I have.

The product prints a self-test report. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. The product aligns the cartridges. http://upintheaether.com/hp-psc/hp-1210-cartridge-error.php Figure : Open the cartridge access door Without turning off the product, disconnect the power cord from the rear of the product.

Solution four: Clear any jammed paper Follow these steps to clear a paper jam from the product. It might take several tries to complete the sequence within ten seconds. Press and release the Copies button. Press and release the Paper Type button.

Check the paper loaded in the paper tray, and then make a note of the paper size and type. Solution nine: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. Check the lights on the control panel to make sure that they are no longer blinking. This video shows how to print a test page Click here to see this video in full screen on YouTube.

Securely connect the alternate USB cable to the computer. If the settings in the Paper/Quality tab are correct, load the size and type of paper specified by the settings into the paper tray. Lots of newer HP printers use the 56 and 57 cartridge set. Figure : Remove the rear access door Press in the tab Pull out the door Lightly dampen a clean, lint-free cloth with bottled or distilled water, and then squeeze any excess

If the issue persists, continue with the next solution. If these steps resolved the issue, you do not need to continue troubleshooting. note: Forcing the paper too far into the product might cause multiple sheets of paper to be fed through the print mechanism, or cause a paper jam. Press in the tab on the left side of the door, and then pull the door away from the product to remove it.

None of the suggested troubleshooting techniques in the user ref manual do any good. Step two: Align the cartridges Follow these steps to align the cartridges. Solution six: Clean the cartridges and inside the All-in-One Follow these steps to clean the electrical contacts on the cartridges and inside the product.