Hp Psc 1210 Error Check Paper
Disconnect the USB cable from the rear of the product. If you use distilled to do this make sure printer is unplugged during...and dry before power up. caution: Do not disconnect the power cord during this step. Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. http://upintheaether.com/hp-psc/hp-psc-1210-check-paper-error.php
You can also purchase genuine HP cartridges from other retailers. Press the On/Resume button () to turn on the product. by unknown on Apr 10, 2010 at 2:22pm Add comment Please sign in to comment 0 I also had this problem. note: If the carriage does not move into the access area, turn the product off and then on again. navigate to this website
Hp Printer Says Out Of Paper But There Is Paper
Load plain, white paper into the paper tray. After you find the pattern that matches your blinking lights pattern, try each solution in the order presented until you resolve the issue. I found a fix although it does require taking the majority of the printer apart to get to the feed roller. Right-click the following link, How to Buy HP, to buy a compatible power cord.
note: An E might also appear in the Copies display. A. If the issue persists, continue to the next solution. Hp Psc 1210 Check Print Cartridge Error The tray contains more than one type of paper.
Figure : Remove scraps of paper Reattach the rear acc Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen... This video shows how to clear a carriage jam Click here to see this video in full screen on YouTube. Step one: Clean the rollers Gather the following materials: A clean, lint-free cloth, or any cloth that will not come apart or leave fibers Distilled, filtered, or bottled water (tap water Anmelden 79 8 Dieses Video gefällt dir nicht?
Press and release the Cancel button () again. Hp Psc 1210 Troubleshooting Any other thoughts? note: If the carriage does not move into the access area, turn the product off and then on again. If the issue persists, continue to the next solution.
Hp Psc 1210 Out Of Paper Error
The printer was smart enough to know it couldn't print - 13library 0 Thanks guys and especially Bert for the advice, though it doesn't work for me.
Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document. http://upintheaether.com/hp-psc/hp-psc-1210-error-check-print-cartridge.php The rear access door might not be closed or is not locked into place. So I guess the document and main printer settings must match if there is a paper feed problem and printer is brand new like mine.Hope this helps anyone having this sort HP Support Forums Join in the conversation. Hp Psc 1200 Series Paper Jam
If the product does not complete the cartridge alignment, it will print an alignment page every time you turn on the product. Scroll to the bottom of the page, and then make sure the country/region location is correct. Do not use paper that is too thin, too thick, or too glossy for the product. http://upintheaether.com/hp-psc/hp-psc-1210-check-cartridge-error.php If these steps resolved the issue, you do not need to continue troubleshooting.
Figure : The location of the carriage contacts Figure : The gold-colored electrical contacts inside the carriage Wait about ten minutes to allow the electrical contacts to dry, or use a Hp Printer Paper Feed Problems Figure : Adjust the paper width guide against the edge of the paper Open the cartridge access door. Press the On/Resume button () to turn off the product.
Figure : Disconnect the power cord Wait 15 seconds.
If the product is unresponsive for more than 60 seconds, continue to the next solution. If the On/Resume light () does not blink, replace the black cartridge. Use a second moistened foam rubber swab or lint-free cloth to clean the gold-colored electrical contacts in the carriage, inside the product. Hp Psc 1350 Manual Disconnect the power cord from the rear of the product.
Wait 15 seconds. An easy fix! - Dauer: 7:47 maximpulse 391.294 Aufrufe 7:47 HP PSC 1210 all in one 복합기 분해하기 - Dauer: 2:02 dorivercom 5.316 Aufrufe 2:02 HP 1210 all-in-one - Dauer: 2:52 Open the back panel and clean the rollers with a damp cloth. this content I know it's not the best solution but it works fine without taking it apart.maybe in the future i will replace the spring with a stronger one.
Or the trash can is the only one? Follow these steps to determine which cartridge is defective, and then remove and replace that cartridge. Disconnect the product cord from any power strip or surge suppressor, and then plug it directly into a three-prong wall outlet. You can change this preference below.