Home > Hp Psc > Hp Psc 1200 Series System Error

Hp Psc 1200 Series System Error

Contents

Figure : Insert the cartridge Firmly push the cartridge in until it snaps into place. Reconnect the power cord to the power module. Do not leave a cartridge outside the product for more than 30 minutes. Flag Permalink Reply This was helpful (0) Collapse - HP 1200 psc by Carazara / June 2, 2005 10:13 AM PDT In reply to: Have you tried any other program to his comment is here

I've been to different forums but the general consensus seems to be that WindowsXP is riddled with problems like this. If these steps resolved the issue, you do not need to continue troubleshooting. Facebook Twitter Google+ YouTube LinkedIn Tumblr Pinterest Newsletters RSS The product aligns the cartridges. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking.

Hp Psc 1200 Driver

Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. HP Download and Install Assistant Close Privacy Policy © Copyright 2016 HP Development Company, L.P. If these steps resolved the issue, you do not need to continue troubleshooting.

note: Forcing the paper too far into the product might cause multiple sheets of paper to be fed through the print mechanism, or cause a paper jam. If the issue persists, continue to the next solution. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). Hp Psc 1200 Driver Windows 7 64 Bit Download Press and then quickly release the On/Resume button () to start a power on/off cycle.

Open the Device Manager:Windows 98 and Me: Select the Device Manager tab. If the issue persists, continue to the next solution. If the product does not complete the cartridge alignment, it will print an alignment page every time you turn on the product. Press the On/Resume button () once slowly to turn on the product.

Do not overload the tray with paper. Hp Psc 1200 Printer Offline Figure : Install the front panel overlay Figure : Correctly installed front panel overlay Reconnect the power cord to the rear of the product. Step one: Install the cartridges Press the On/Resume button () to turn on the product. Wait until the On/Resume button () is steady.

Hp 1350 Printer Check Print Cartridge Error

When prompted, you plug in the USB cable. http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/hp-psc-1200-all-in-one-printer-does-not-print-says/394fb111-6de9-47b5-a4e5-2ced0a1671c2 With the power on, disconnect the power cord from the rear of the product. Hp Psc 1200 Driver If the issue persists, continue to the next solution. Hp Psc 1210 Driver Download An obstruction is blocking the paper path.

If the issue persists, continue with the next solution. this content I have been to HP's site and tried updating drivers but still the problem persists. Disconnect the power cord from the rear of the product. Step one: Clean the electrical contacts on the cartridges and inside the product Gather the following materials: Dry foam rubber swabs, a lint-free cloth, or any soft material that will not Hp Psc 1200 Driver Windows 7

Press and release the Paper Type button. Solutions Solution one: Wait for the All-in-One to complete the job The product is processing a copying, scanning, printing, or photo or maintenance job. Press and release the Color Start Copy button. weblink Thank you for helping us maintain CNET's great community.

If the issue persists, continue to the next solution. Hp Psc 1210 Check Print Cartridge Error caution: Do not disconnect the power cord during this step. The product aligns the cartridges. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking.

Figure : Open the cartridge access door Hold the cartridge on its sides, and then slide the cartridge forward into its slot at a slightly upward angle.

Do not use paper that is too thin, too thick, or too glossy for the product. Only add paper to the tray when the product is not printing. If you press the On/Resume button () again during this time, you might turn the product off. Hp Psc 1200 Series Windows 7 Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults.

If these steps resolved the issue, you do not need to continue troubleshooting. If the issue persists, continue to the next solution. If the alignment page does not print automatically, follow these steps to print one manually: If the product is off, press the On/Resume button () to turn on the product. check over here If the product does not complete the cartridge alignment, it will print an alignment page every time you turn on the product.

Press the Cancel button () on the control panel. If the product is unresponsive for more than 60 seconds, continue to the next solution. Figure : Disconnect the power cord Wait 15 seconds. by unknown on Mar 2, 2009 at 2:58am Add comment Please sign in to comment 0 I tried what the anonymous blogger wrote, but it still didn't work!

If you email me at [email protected] I will be glad to send you the EZinstall file. Solutions Solution one: Wait for the All-in-One to complete the job Allow the product to complete the job. Product Number * Example: C8375A, B8F40EA, H1P31AA Privacy Policy © Copyright 2016 HP Development Company, L.P. note: If the carriage does not move into the access area, turn the product off and then on again.

Reach inside the product through the cartridge access door, and then manually move the carriage. The product makes loud grinding noises. It helped a little bit to uninstall the printer completely and reinstall it. by nandita on Dec 11, 2015 at 12:42am Add comment Please sign in to comment Please sign in to comment HP DeskJet 3420 Buy discount ink Buy this printer More HP

If you cannot cancel the task, press and hold the On/Resume button () for three seconds to turn off the product.