Home > Hp Psc > Hp Psc 1200 Error Codes

Hp Psc 1200 Error Codes

Contents

If the issue persists, continue to the next solution. Melde dich bei YouTube an, damit dein Feedback gezählt wird. note: You might need a flashlight to illuminate areas for proper viewing. No more paper jams! his comment is here

An alignment page prints automatically. First Time Here? Figure : Remove the cartridge If the cartridge has protective tape covering the nozzles, use the pull tab to remove it. The system returned: (22) Invalid argument The remote host or network may be down.

Hp 1350 Printer Check Print Cartridge Error

Use both hands to pull any whole sheets of paper to avoid tearing them. Wird geladen... If the product completes the job normally, there is no need to continue troubleshooting.

González 3.421 Aufrufe 2:05 COMO DESCARGAR & INSTALAR EL DRIVER DE HP PSC1315 - Dauer: 4:41 Gabriel Matias 34.652 Aufrufe 4:41 เครื่องใช้สำนักงาน {HP PSC 1315 ALL IN ONE} - Dauer: 2:52 Issue: The On/Resume and Black Start Copy lights blink In this normal condition, the following blinking lights pattern displays on the control panel: On/Resume light: Blinking Check Paper light: Off Check Step two: Try the task again Press the appropriate button(s) on the product control panel to try the intended task again. Hp Psc 1350 Manual How does HP install software and gather data?

Gently lower the tray until it is horizontal and stops. Hp Psc 1210 Check Print Cartridge Error Step one: Perform a power reset Press the On/Resume button () to turn on the product. Hochgeladen am 18.06.2010Learn how to fix the HP PSC 1200, 1205, 1209, 1210, 1210v, 1210xi, 1213, or 1215 All-in-One printer when it doesn't pick up or feed paper, or you get http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00461967 Solution two: Load paper Follow these steps to load letter or A4 paper into the product.

I just installed a new cartridge a week or so ago, and it worked fine for the first 2-4 prints...then all of a sudden all of the lights started blinking, including How To Reset Hp Psc 1410 Printer The color cartridge belongs in the slot on the left. Press and release the Cancel button () again. We have not detected any issues with your product.  You may find a relevant support option by selecting any of the helpful topic tabs on this page or by entering your

Hp Psc 1210 Check Print Cartridge Error

If the carriage is stuck on the left side of the product, move the carriage to the right side of the product. Press and release the Cancel button () again. Hp 1350 Printer Check Print Cartridge Error Issue: The On/Resume light blinks for 3 seconds and then remains on, and the Black Start Copy and Color Start Copy lights blink In this normal condition, the On/Resume light () Hp Psc 1210 Troubleshooting Disconnect the USB cable from the rear of the product.

Step one: Remove any loose paper Remove any loose sheets of paper from the input tray and the output tray. this content Diese Funktion ist zurzeit nicht verfügbar. The reset is now complete. If the message on the computer does not identify a particular cartridge (it says only Print cartridge error), follow the steps below to determine which cartridge is causing the problem. Hp Psc 1315 Check Printer Cartridge Error

Figure : Reinsert the cartridge Firmly push the cartridge in until it snaps into place. Check the electrical outlet to make sure that the power cord is securely plugged into it. Paper jam causes The following factors can cause paper jams: Paper loaded incorrectly in the paper tray. http://upintheaether.com/hp-psc/hp-psc-1200-paper-jam-error.php Figure : Lower the paper tray You might have to press the On/Resume button () again to resume the task.

If the issue persists, continue to the next solution. Hp Psc 1210 Reset Disconnect the USB cable from the rear of the product. The reset is now complete.

This tool will detect HP PCs and HP printers.

Press and hold the Cancel button (). If these steps resolved the issue, you do not need to continue troubleshooting. If these steps resolved the issue, you do not need to continue troubleshooting. Hp Psc 1350 Troubleshooting Anmelden Statistik 19.097 Aufrufe 4 Dieses Video gefällt dir?

If the alignment page does not print automatically, follow these steps to print one manually: If the product is off, press the On/Resume button () to turn on the product. Do not overload the tray with paper. Wird verarbeitet... check over here HP Customer Support Support Home Products Software and Drivers Forums Contact Support Search Select your Model Let HP find my products Identify now HP can identify most HP products and recommend

Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar. Trying to clear jammed paper from the front of the product can damage the print mechanism. Dip a clean foam rubber swab or lint-free cloth into distilled water, and then squeeze any excess water from it. The sequence must be completed within ten seconds.

If the LED does not light up, contact HP to replace the power module. Scroll to the bottom of the page, and then make sure the country/region location is correct. Figure : Open the cartridge access door Without turning off the product, disconnect the power cord from the rear of the product. The product prints a self-test report.

Close the cartridge access door. note: If the carriage does not move into the access area, turn the product off and then on again. note: An E might also appear in the Copies display. Personally, what printer(just printer), would you recommend under $150?

Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. When only the On/Resume button () is blinking, release both buttons. The product prints a self-test report. note: If the carriage does not move into the access area, turn the product off and then on again.

Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults. Solutions and updates HP has detected possible issues with your product. Contact HP to replace the power cord. Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults.

Insert the paper into the paper tray print side down until it stops. Remove any loose paper Do not pull jammed paper Step two: Clear the paper jam from the rear of the All-in-One caution: Always try to pull jammed paper from the rear