Home > Hp Printer > Hp Printer Error Code 60.2

Hp Printer Error Code 60.2

Service Manual Requests Business Talk For Sale, Trade, or Wanted The Parts Room Employment Non-Technical Forums Rants, Raves, and Everything Else Arcade Discussion Industry News Test Forum « HP 9850 MFP Tray 4 lift motor error has occurred.2. Figure 2: Lifting the paper-access plate Slowly pull the jammed paper out of the printer. Figure 13: Opening the top cover and removing the print cartridge Use the green handle to lift the paper-access plate. his comment is here

alternates with 68.X PERMENANT STORAGE ERROR To continue press (Select) Description One or more printer settings that were saved in the nonvolatile storage device are invalid and have been reset to In addition the 14T Gear has been raised to improve contact between the tray and the lift drive gears (raised by about .3mm). - RM1-1088 500-sheet tray 4200/4250/4300/4350 Symptom #2 Slide the tray out of the printer, and remove any damaged paper from the tray. Install the tray and listen carefully. visit

Replace the tray if necessary. 5. Action Turn the printer power off and then turn the printer power on. Action Press Cancel Job to clear the job from the printer memory. Plug the printer into a wall outlet and see if this resolves the problem.

Figure 54: Removing the tray Pinch the release that is located on the left guide and slide the side guides to the correct paper size. Also ensure the teflon coated polyester film sleeve is intact. The lift mechanism has been is use since the LaserJet 4200 was introduced in 2002 so HP clearly regard it as a reliable solution. Action If the printer displays this error then please contact HP Support.

If the toner gets on clothing, wipe it off with a dry cloth and wash the clothing in cold water. If the error persists, turn the printer off. Lift the optional duplexer up and then pull it out to remove it. http://www.copytechnet.com/forums/hp/27131-my-hp-4200-laser-printer-gives-me-60-2-error.html I chased my tail on one of these the other day, and it was all due to a setting in the print properties. :-)PCRMike by pcrmike on Oct 16, 2006 at

Lift drive assembly will have to be removed to perform this repair. Make sure it locks into place. Figure 28: Closing the rear door If the error persists replace the stapler/stacker or stacker. Print a Configuration page and verify that the tray settings match the media in the tray.

If replacing the Lifter Drive Assembly does not correct the issue, the DC Controller could be at fault. It has 3 ribs on the right side of the tray rails to eliminate this problem. Reply With Quote 11-09-2009 #5 ExOceMan View Profile View Forum Posts Private Message Trusted Tech 50+ Posts Join Date Sep 2009 Location Seattle, Washington Posts 63 Post Thanks / Like Thanks If the accessory uses cables, disconnect and reconnect them.

If the sealing tab cannot be removed, insert a new print cartridge and return the faulty print cartridge to receive a replacement. this content Loading Laser Printer Repair and Fax, Copier Service ArticlesThis Website is Dedicated to Providing Free Service and Repair Articles Designed to Help Service Technicians or End Users Fix Their Printer, Copier, alternates with 59.XY PRINTER ERROR To continue turn off then on 59.2 MAIN MOTOR ROTATION ERROR 59.4 EP MOTOR ROTATION ERROR (HP LaserJet 4300 only) 60.X PRINTER ERROR 62 NO SYSTEM Replace the lift motor for the tray if necessary.

Figure 51: Closing DIMM access door Set the bottom of the cover onto the printer. Action NOTE: Press the ? (help) button for detailed information about clearing the jam. Unhook the tension spring (callout 3). weblink To view Help for a message (if available), press (Help).

Defective formatter board. 2. NOTE: Avoid spilling loose toner. Make sure the bottom tab on the cover fits into the corresponding slot in the printer.

Open and close the top cover to clear the message.

make sure to check the correct connector on the associated HCI PCA for the 3 x 500 sheet feeder. 7. Technical Forums Copier Technical Discussion Canon Konica Minolta Kyocera Mita, Copystar Muratec Panasonic Ricoh, Savin, Gestetner, Lanier Sharp Samsung Toshiba Xerox Other Copier Brands Fax & Printer Technical Discussion Brother Canon Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers Home Forum New Posts FAQ Calendar Community Groups Albums Member List Thanks / Like Statistics Hottest Threads / Posts Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders

Action NOTE: Press the ? (help) button for detailed information about clearing the jam. Refer to the following instructions for additional information about adding more memory: NOTE: If you have not already done so, print a Configuration page to find out how much memory is If the message persists print a Configuration page and check the printer settings to determine which values have changed. (To print a Configuration page, open the Information menu at the printer check over here by wlulham on Oct 30, 2006 at 9:11am Add comment Please sign in to comment 0 Lt Skitz,Half cycle test:Run a test page, (feed paper from tray 1),just as the trailing

Open and close the top cover to clear the message. Check tray for obstruction. alternates with 41.X PRINTER ERROR To continue press (Select) Description A temporary printer error has occurred. If the above action does not solve the issue, contact HP or authorized service provider.

Figure 25: Inserting staple cartridge The stapler needs to reload after clearing a staple jam, so the first few documents (up to five) might not be stapled. Action Press the (Select) button to continue. If the message persists, contact HP Customer Support. Symptom #3 Pull tray feed shaft to the left.

Action NOTE: Press the ? (help) button for detailed information about clearing the jam. Moved the stop up and problem solved. HP LASER PRINTER 9000, 9040, 9050MFP ERROR 60.2 IS TRAY 2, 60.3 IS TRAY 3 1. Replace the EIO accessory in slot [X].

by dmzcompute on Jul 2, 2004 at 10:49pm Add comment Please sign in to comment 0 I keep getting this error saying there is a paper-jam in the rear door, but If the above action does not solve the issue, contact HP or authorized service provider. They offer information about normal printer operation and no interaction is required to clear them. Pick-up Assembly Loose The pick-up assembly is missing the bushing, gear, or both, which causes the assembly to be loose.

Figure 41: Installing rear-output bin Plug the power cord into the printer. If the later it would take a toll on the fuser. This connector is for Tray 2 and Tray 3 lift motors and sensor switch assemblies. 6. Reload the paper and close the tray.