Hp Printer Error Code 50.2
Any ideas on where to go next? by unknown on Oct 5, 2007 at 4:08pm Add comment Please sign in to comment Oh and if it says 220-240v then its EU - Anonymous so I have a 4200 I got it figured out on my own though, thanks for the information I got off of here. Need help from somebody out there Thanks Fred Reply 0 Reply 0 0 Everyone's Tags: HP LaserJet 4250n View All (1) davidzuts Regents Professor Posts: 4,703 Member Since: 01-17-2009 Message 2 his comment is here
by sfe39 on Jan 18, 2006 at 4:20pm Add comment Please sign in to comment I don't know if you read my reply, but I run the fixyourownprinter site. by unknown on Mar 18, 2009 at 7:12pm Add comment Please sign in to comment 0 I just changed my fuser and it was a 220v, but I followed the instructions Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting Now I got the same message again, but unfortunately the warranty is no longer valid.Does anyone have any ideas on how to get the fuser out to check it ? http://www.printertechs.com/printer-troubleshooting/11-50-2-fuser-error
by sstuart on Dec 26, 2006 at 11:29am Add comment Please sign in to comment I have seen alreasy about a dozen printers where the wrong fuser has been installed. Reply 0 0 SHThompson Distinguished Professor Posts: 2,711 Member Since: 05-09-2011 Message 3 of 3 (849 Views) Report Inappropriate Content Re: hp laserjet 4250n 50.2 fuser error Options Mark as New by 87vert on Jan 2, 2007 at 3:54pm Add comment Please sign in to comment 0 replaced the dc controller last night, same problem, is that the low voltage power supply The screen says to turn it off, then back on and if the issue persists, to call a tech.
by Anonymous on Oct 15, 2009 at 11:44am Add comment Please sign in to comment 0 How much is the heating element for the Error 50.2 HP Laserjet 5000...looks like I W = 2: Reconnect the connector (J62) on the low-voltage power supply PCA.5. by dmzcompute on Jan 2, 2007 at 3:28pm Add comment Please sign in to comment 0 thank you, i will order the parts and report back. We stock the fuser heating assemblies.
by dmzcompute on Jan 29, 2012 at 7:35am Add comment Please sign in to comment 0 The fuser would have also blown if the unit was plugged into 220V. I tried booting it without the network cable. I did see on some blogs, people were talking about possible power issue/voltage issue. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.
I tried booting it without the network cable. Showing results for Search instead for Do you mean or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the I noticed when powering on the machine the fan didn't come on. I work for HP.Best Regards,Kenneth Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP
Easy to replace, just drop down the back cover, release the plastic strap which holds the door from falling down, move to one side and the back comes off. Thank you! Register · Log In HP Support Forum Home > Printers > LaserJet > hp laserjet 4250n 50.2 fuser error HP Support Forums Join in the conversation. I've got both 110V and 220V in stock. If no, then you got a defective fuser and you need to return it for replacement.
If the fuser doesn't heat, the printer should not run and you should get a 50 error. this content so that doesn't normally enter into the troubleshooting I do. If you were getting the error before, then you may have an issue with your dc controller or low voltage power supply. by 87vert on Jan 2, 2007 at 3:07pm Add comment Please sign in to comment I am having the same problem exactly I changed power supplyfuser dc controller printer wont cycle
Thank you! Register · Log In HP Support Forum Home > Printers > Inkjet > 50.2F.00 fuser error HP Support Forums Join in the conversation. No more fusion problems. Now turn the printer on and when the memory starts to count in the display, hold and keep holding the green check mark button on the right until all three lights weblink keep up the good work by unknown on Mar 19, 2008 at 1:51am Add comment Please sign in to comment 0 In the USA we use 110 to 127 volts out
Click the Kudos on the left side for helping and click Accept as Solution for providing a solution.
Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting Replaced the fuser and other parts from maintenance kit. The part number is verified. You need to replace the fuser.
I replaced it but when I power on HP I get Fuser Error 50.7 all the time along with clicking noise on the fuser. This is an international forum, after all. No joy, same error. Keep in mind most times you get a 60 error is the tray does not lift.
I had this problem with a 4200 changed the fuser it's now working ok. - Anonymous 0 Next item would be the dc controller, followed by the power supply. HevnLghI work on behalf of HPClick the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping! I work on my HP DesignJet 430, and service my own car, so working on it doesn't scare me. Just the fact some of the questions are from people who live elsewhere so it can get confusing and sometimes the wrong information can be relaid back of what parts you
First Time Here? I'm getting aquote on a fuser, and hope to install it myself in the next couple of days. Since it was only getting half the voltage it was supposed to be getting, it wasn't getting hot enough to fuse the toner, but it didn't trip the error either. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video,
Is this something I can handle myself? One of the good numbers to call is 1-800-474-6836 and select the options for the printer. by moe on Jan 18, 2006 at 4:36pm Add comment Please sign in to comment 0 I have replaced the fuser. and may not be used without advance written permission of PrinterTechs.com, Inc.
Click on my name and email me for pricing and ordering info.