Home > Hp Printer > Hp Printer Error 80.x

Hp Printer Error 80.x

Formatter PCA malfunction. 3. X Description 2 Fan 3 - Formatter Fan (intake) 3 Fan 2 - Laser/scanner (exhaust) 5 Fan 1 -Low-voltage power supply (exhaust) 6 Fan 4 - Face-down delivery (exhaust) 9 Fan ERROR 59 Add Memory 4Si/IIISi Not enough memory for PostScript option. TouchWirelessSettings, touchWireless Setup Wizard, and then follow the onscreen instructions.Make sure the computer or the mobile device is connected to the wireless networkMake sure your computer or mobile device is connected his comment is here

Some non-HP parallel cables might be missing pin connections or might otherwise not conform to the IEEE-1284 specification. Check tabs on side of toner cartridge. Inspect toner level sensor connector for damage. 4. II,III Only: 1. have a peek here

alternates with 41.X PRINTER ERROR To continue press (Select) Description A temporary printer error has occurred. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2. Reply 0 0 Csabee Student Posts: 1 Member Since: ‎08-04-2015 Message 5 of 6 (797 Views) Report Inappropriate Content Re: error code 0XB80A1A58 on a new DJ3540 printer Options Mark as

Replace Formatter PCA. 3. Thank you! The media is probably wrapped around the fuser roller. Turn the printer power off, install it in a different EIO slot, and turn the printer power on.5.

Action NOTE: Press the ? (help) button for detailed information about clearing the jam. Remove any jammed paper from the stapler/stacker. Check PS102 and PS103 13.5 Paper delay jam at fuser. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422 How did we do?

Turn the printer power off, and then replace the DIMM that caused the error. Action Turn the printer power off and then turn the printer power on, if the error persists, contact HP or an authorized service provider. Verify the tab on the cover is not broken. X=2: Laser malfunction. 52 ERROR (Incorrect Scanner Speed) 1.

Remove and reinstall the supply, replace the supply. Continued AUTO CONTINUE has two settings, OFF and ON (the default). Replace DC controller. Remove any paper found.

If the error persists, turn the printer off. this content NOTE: If the top cover does not close, make sure the print cartridge is correctly installed. alternates with 64 PRINTER ERROR To continue turn off then on 66.00.15 EXTERNAL DEVICE FAILURE 66.12.XX OUTPUT DEVICE FAILURE For help press? 68.X PERMANENT STORAGE ERROR For help press ? top 64 PRINTER ERROR For help press?

Add more memory. The printer cannot process the page quickly enough. Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers http://upintheaether.com/hp-printer/hp-printer-error-printer-is-offline.php DC Controller PCA malfunction.
12 OPEN or NO TONER or NO EP IIP/IIP+/IIIP Only: 1.

X represents the error location and can equal one of the following: 1 = Slot number 1 2 = Slot number 2 3 = Slot number 3 6 = Card in Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA. 4. Disassemble clutch and re-grease.

If the error does not clear, replace the duplexer.

is between 2925J00000 to 3047J999999. (2-diode to 3-diode upgrade corrects static caused problem.) IIP, IIP+, IIIP Only: 1. Figure 16: Opening Tray 1 and removing entrance cover Rotate the paper guide to check for additional jammed paper underneath. Action Turn the printer power off and then turn the printer power on. If the above action does not solve the issue, contact HP or an authorized service provider.

If the message persists, contact HP Customer Support. Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants. Action Press the (Select) button to resume printing. check over here The stacker or stapler/stacker LED is continuously illuminated in amber.

Replace the EIO accessory in slot [z]. Other causes include poor quality parallel cables, poor connections, or specific software programs. Check and reseat connectors J4, J5, on the Low Voltage Power Supply, J8, J9, J10 and J15 on DC Control PCA. 2. Reply 0 0 rusznakz Student Posts: 1 Member Since: ‎07-01-2015 Message 3 of 6 (913 Views) Report Inappropriate Content Re: error code 0XB80A1A58 on a new DJ3540 printer Options Mark as

Replace fuser. 2. Disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize.2. If error is gone replace each EIO device until error appears. Bad fuser Exit Sensor (PS3). 5Si Only: 1.

It can also be caused by a defective DC controller. Figure 19: Reinstalling the print cartridge and closing the top cover If a jam message persists, jammed paper is still jammed in the printer. Replace the network card. Bad Fuser Safety PCA. (P/N RG1-0208-030.) Note 2686A/D: Short resistor R250 on the DC Controller to bypass error 50 time delay.

Make sure it locks into place. Remove and reseat the optional interface card. Print a configuration page and check the printer settings to determine which values have changed. 68.X PERMANENT STORAGE FULL The printer’s permanent storage is full. Is the paper size correct?

Warning messages Warning messages display information about data and print errors.