Home > Hp Photosmart > Hp Photosmart C7200 Fax Error

Hp Photosmart C7200 Fax Error

If the error persists, and error correction is in use for the fax session, disable ECM. Off On (Fax Send) On (Fax Receive) Send & Receive To include an image of the fax on the report 1. Video should be smaller than 600mb/5 minutes Photo should be smaller than 5mb Video should be smaller than 600mb/5 minutesPhoto should be smaller than 5mb Related Questions Trying to send 10-mb Reconfigure the local fax machine to use different configuration settings, enable or disable the ECM setting. 223 ECM 224 The local machine was unable to receive an entire page even after his comment is here

Use the tables in this document to view fax error codes and solutions. This error is very rare because normally a remote machine does not answer if it cannot receive a document. Print This PagePrint ShareShare Url of this page: HTML Link: Bookmark Manuals Brands HP Manuals All in One Printer OFFICEJET 7500A User manual HP OFFICEJET 7500A User Manual: Print Fax Error Ask the remote machine user to reset the remote machine. http://www.support.hp.com/us-en/product/hp-photosmart-c7200-all-in-one-printer-series/3204782/document/c01083799/

Touch Fax Confirmation with image. Click here for instructions on enabling and disabling ECM (c00060802) (in English).Try sending at a lower transmission speed.This document is a great place to start for general fax problems. I have set the J6480 touse the same line that our other fax machine used before it died on Tuesday, (Ricoh fax/copier).

Have the sender send at a lower resolution. When I try to open window send one friend messages. Call the telephone provider if line conditions fail to improve. Prints whenever a fax error occurs.

Solution: 1. This error does not result in the session being terminated immediately. I faxed over from a hp photosmart c6180 all in one series printer. Select a slower reception speed. 225 The remote machine attempted to initiate a remote diagnostic session with this machine even though remote diagnostic access is locally disabled.

getting an error message 351 when trying to fax. The user called the correct number, but the machine was configured not to answer. Reduce or enlarge the page size setting on the local machine to a size supported by the remote machine. 319 The local machine attempted to initiate a binary file transfer (BFT), No action required. 311 The user of the local machine pressed the Stop key, causing the session to be prematurely terminated before all pages have been sent.

This situation occurs rarely. http://www.manualslib.com/manual/71248/Hp-Photosmart-C7200.html?page=152 Tried sending fax to friend got message error 388? Reconfigure the local fax machine to use different configuration settings, enable or disable the ECM setting. 245 ECM 246 ECM The user of the remote machine pressed the Stop key, causing Ask IT Technicians for Answers ASAP Not a Printers Question?

Don't show me this message again. http://upintheaether.com/hp-photosmart/hp-photosmart-325-error.php There was a communication error with the sending fax machine. Definition Error code 387:There is too much noise on the line for a valid connection between two fax machines to complete. These errors can occur if the phone lines in the area to be faxed are old or there is noise (static on the phone line).

Privacy Policy © Copyright 2016 HP Development Company, L.P. Reply 0 Reply 0 0 Super_Dave PhD Student Posts: 945 Member Since: ‎01-10-2011 Message 2 of 2 (1,079 Views) Report Inappropriate Content Re: photosmart c7200. These errors can occur if the phone lines in the area to be faxed are old or there is noise (static on the phone line). weblink Contact the sender to make sure a document is ready and correctly loaded in the sending fax machine.

If these transmissions are successful, then notify the user of the remote machine to make them aware of the issue. To a hp office jet k80 all in one printer. Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting

Configure the remote machine for poll transmission.

Depending on your printer, a fax error code might display on the printer control panel or on a fax history report. On many fax machines, it is possible to accidentally initiate a fax reception in the following cases: There is no paper in the machine. Disable ECM, and then try faxing again. Call the telephone provider if line conditions fail to improve.Disable ECM.

No solution is available because the two machines are incompatible. 318 The remote machine cannot support a fax reception at the page width selected by the local machine. Press to highlight Fax Log, and then press OK to print the Fax Log. Confirm that the remote caller is a fax machine and not a voice call. check over here Wait several minutes between the end of one transmission and the start of the next transmission. 383 ECM Disable ECM, and then try faxing again.

Ifafax transaction had anerror, the error isindicatedby anerror codeinthefaxlog.Ifnecessary (forsecurity purposes, for example), you caneasilycleartheentirelog frommemory.Thisalsodeletes anysaved faxes frommemory.Toprint thefaxlogfromthecontrolpanel1.PressSetup.2.PresstohighlightPrintReport, and then pressOK.ThePrint Reportmenuappears.3.PresstohighlightFax Log,and thenpressOKtoprint theFax Log.Print reports151Printreports and forms Any suggestion.