Home > Hp Officejet > Hp Officejet Pro K5400 Mc Error

Hp Officejet Pro K5400 Mc Error

Contents

Die Bewertungsfunktion ist nach Ausleihen des Videos verfügbar. The product is processing a print job. If the carriage is stuck on the left side of the product, move the carriage to the right side of the product. Remove the rear access door. navigate here

Open the cartridge door. Allow the carriage to move to the access area. Filter By: flashing print mc k550 blinking light ink 105 questions posted Ask a Question Usually answered in minutes! Press the button on top of the duplexer, and then tilt the door toward you to open it.

Hp Officejet Pro K5400 Troubleshooting

Figure 67: Insert the cartridge and close the cartridge door If these steps resolved the issue, you do not need to continue troubleshooting. Wird geladen... You did say that immediately after you installed the new cartridges, everything worked great--I'm assuming that means no print quality problems with any of the colors. If the test page does not print, continue with the next solution.

Reconnect the USB cable or the Ethernet cable to the rear of the product. Open the cartridge door. Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting Cancel Ok Privacy Policy © Copyright 2016 HP Development Company, L.P.

Insert the door into the rear of the product, and then gently push it forward until it snaps into place. Learn more You're viewing YouTube in German. You either have a bad ink cartridge or you have a bad printhead. Wait at least 15 seconds.

Help; Knowledge base options.Get Free DIY printer repair advice from experts with over 25 years experience servicing HP, Epson, Canon and other inkjet and laser FixYourOwnPrinter.com.I have a one month old Press the Power button () to turn on the product. Figure : Open the cartridge door Remove the cartridge indicated by the blinking light on the control panel. Follow these steps to try clearing the error message by resetting the product.

Hp Officejet Pro K5400 Clean Print Heads

Solution four: Replace the printhead Make sure that plain white paper is loaded in the input tray. Unplug the power cord from the wall outlet. Hp Officejet Pro K5400 Troubleshooting Press down firmly on the latch to make sure that it closes completely. Hp Officejet Pro K5400 Manual Align the cartridge with its color-coded slot, and then insert it into the slot.

Figure 36: Lift the printhead latch Raise the handle on the printhead that is indicated by the blinking light on the control panel, and then use the handle to remove the check over here Solution two: Check the rear access door or the duplexer Your product has either a rear access door, or a two-sided printing accessory (duplexer). Figure : Remove the duplexer Carefully remove any jammed paper and bits of torn paper from the rollers inside the product. More Support Options Related Videos - of Video Tutorials | Show all Show less HP Download and Install Assistant HP Download and Install Assistant makes it easy to download and install

Flashing KY. Figure : Lights and buttons on the product control panel Print Cartridge lights Printhead lights Configuration Page button (available on some models) Cancel button Resume light Power light The following sections NOTE: If the paper tears when you remove it, check for any torn pieces of paper inside the product. his comment is here Press down firmly on the cartridge until it clicks into place, and then close the cartridge door.

Go to HP SureSupply. Figure 3: Remove the rear access door Carefully remove any jammed paper and bits of torn paper from the rollers inside the product. HP Officejet K550--2 lights (KY & MC)are NOTHING prints ??

Country: United States Select a location Americas Europe, Middle East, Africa Asia Pacific and Oceania Select a language Confirm Back Z7_M0I02JG0KOT530A6KJKFRQ0816 hp-detect-load-my-device-portlet Actions ${title} Loading...

Press down firmly on the latch to make sure that it closes completely. Open the cartridge door. Figure : Example of the estimated ink levels graphic If one or more of the cartridges are low on ink, consider replacing the cartridges. Figure : Open the duplexer access door With the damp cloth, clean the rollers inside the duplexer.

Wait for the product to initialize the printheads and print an alignment page. Press down firmly on the latch to make sure that it closes completely. Solution three: Clean the printhead electrical contacts Make sure that plain white paper is loaded in the input tray. weblink Lift the printhead latch.

If the issue persists, continue to the next solution. The obvious answer is to reseat the print heads, but I'm guessing you've already done that with the same result (same flashing lights), is that correct?UPDATED: at the same time I Figure : Insert the cartridge and close the cartridge door Issue: The Power light and one or more Print Cartridge lights blink In this error condition, the following light pattern displays Align the cartridge with its color-coded slot, and then insert it into the slot.

Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Wait 20 seconds. Ask IT Technicians for Answers ASAP Not a Printers Question? Use the cloth to clean the electrical contacts inside the printhead slot.

Transkript Das interaktive Transkript konnte nicht geladen werden. Loading...Oops :Please try again. Solution two: Remove and reinsert the printhead Improper printhead placement or installation might cause a printhead error. Trying to clear jammed paper from the front of the product can damage the print mechanism.

Lift the printhead latch. Insert the duplexer into the rear of the product, and then push it forward until it snaps into place. Figure 38: Printhead electrical contacts and ink nozzles 1 - Electrical contacts 2 - Ink nozzles (Do not touch) Place the printhead on a sheet of paper or a paper towel. Please return to the product information page and verify the numbers provided or try again later. © Copyright 2016 HP Development Company, L.P.

But it still gives me that yellow paper jam light. Figure 9: Remove paper from the front of the product Step four: Clear the paper jam from Tray 2 If you installed Tray 2, use the following steps to check for Try the troubleshooting steps shown here.