Home > Hp Officejet > Hp Officejet 7130 Error

Hp Officejet 7130 Error

Privacy Policy Terms of Use Sign Up Login Add Question joe979xx asked Apr 19, 2005 at 2:39pm 0 HP OfficeJet 7130 HP Officejet 7130 - Scanner failure? It will not go away and I cannot copy or do anything. Thanks - Anonymous I have the same problem, even after setting the date/time, it resets itself to "Jan 00 00 00:00a" after powering the unit off.Have you had any luck in It would be wonderful if everything worked as its SUPPOSED to!! navigate here

It could be other parts or problems with the service station e.g. Clean! Credentials confirmed by a Fortune 500 verification firm. If I turn the printer off it goes back to Jan 000000000 I have reset the time 5 time I even changed the battery thinking it must be a dead battery, click to read more

The drive belt can be loosened by pressing on belt tensioner on the far left. HP finally said that our scanner bulb might be going bad. Read more Published on July 5, 2009 by malibukid22 1.0 out of 5 starsNot Dependable I bought this product 4 years ago to use with my home-based business. While that once was thought to be a certain sign of a bad logic board, I have discovered this is not absolute and in some cases has been resolved without replacing

I noted a huge amount of dried ink powder silting out of the venting holes of the motor housing. And we don't know for sure that the problem is the bulb. The battery is now completely out of my printer and it works fine. So thanks everyone for all your posts!

To learn more about Amazon Sponsored Products, click here. I think I have determined that my problem is motherboard failure. The 48 bit scanner makes it a great machine to capture photographs and documents with amazing detail.The copy feature has done nothing but improve in these machines over the last few http://fixyourownprinter.com/posts/24476 Your power adapter (supply) block(s) have a blown fuse or have not been re-connected following the routine which causes their internal surge protection to reset itself and allow power through. (These

Respond to this 13 We have an HP Officejet 7130xi in our office and their is a cariage error. Also there is a notice box showing me my docs. The steps below will clear the error condition, which should solve the problem if it is caused by an incorrect detection of air. The drawback is that the printer date now reads Jan 00 00 00.

To remove the Lift panel from the shaft and springed "stay up mechanism, lift the two clips on the backside and slide the panel out.8. http://www.justanswer.com/printers/3o9lk-hp-officejet-7130-one-keep-getting-error.html The ADF should come free much smoother this way. - PrarieCat 0 The instructions on this thread are really great! Was this review helpful to you? The printer worked well, except for the feeder, which usually pulls through more than one sheet at a time.

Feedback Aver Information VC520 All-in-One Video and Audio USB Conference Camera System 4.8 out of 5 stars 17 $949.99 Prime Feedback 10Ft Long HiSpeed Gold Plated USB2.0 Printer Cable IPAX® for check over here Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Published 15 months ago by Terry Pulvidente 1.0 out of 5 starsPoor Product - So Many Errors HP 7310This product has had so many problems since I bought it. Ask AnswerManCharles Your Own Question AnswerManCharles, Technician Category: Printers Satisfied Customers: 347 Experience: 27 years service on office equipment from all manufacturers. 34774669 Type Your Printers Question Here...

With one hand press and hold the # and 6 buttons on the front keypad, then use the other to reconnect the power cord on the back while keeping the buttons Shortening the standby time will cause some extra waiting at times for the scanner to warm-up. I sprayed and wiped them with windex.... http://upintheaether.com/hp-officejet/hp-officejet-630-error.php the cartridges are good.

characters left: Contact Us|Terms of Service|Privacy & Security|About Us|Our Network © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 125 6171032 Login|Contact Us Printers Printer Repair Questions? At first the scanner assemble would move from right to left when it came on. I left the middle front screw from the underside out, so I could clean more frequently.

That's the way I do it.

If you search for videos with this title, you will find it. Thanks. by arthurlewis on May 25, 2006 at 4:44pm Add comment Please sign in to comment Did you ever get a resolution to your scanner failure -power off and on message. this is the most ambitious "fix" I've ever attempted on a printer, other ones I was mainly swapping parts between 2 units.

Four times I took it apart, cleaned, put it back together, tested it, and then read this string again. The print carriage moves to the center.# XXXXX two or three seconds, then unplug the power cord.# XXXXX the printhead latch. There is a connector you have to disconnect as well. weblink I think they do this to prevent folks from refilling or buying re-manufactured cartridges.5 - Adobe Acrobat 6's "Scan to PDF" feature doesn't seem to work with this printer.

It doesn't seem to serve any useful function and I don't see why leaving it off would change things. I did the reset procedures and it worked for a couple days but locked up again. Reply With Quote 03-11-2010,08:21 AM #3 aitnewbie View Profile View Forum Posts View Blog Entries View Articles Junior Member Join Date Mar 2010 Posts 3 Ok what if this does not I hope Adobe & HP can work together to get full Acrobat support for the 7130 in a future update from either company.Haven't used the fax feature so I can't comment.

My officejet d135xi does that and I'm waiting for a solution. putting a printer cartridge in.Thanks for all your help.Nigel by nigel54321 on Oct 8, 2007 at 2:56am Add comment Please sign in to comment 0 Nigel,The battery is held in place I sent an email to it, and nothing happened until the printer started clattering.