Home > Hp Officejet > Hp Officejet 6110 Scanner Error

Hp Officejet 6110 Scanner Error

Contents

About Us We're a forum dedicated to providing support and advice for motherboards, chipsets and drivers from all manufacturers. Once open all I did was clean the glass and my printer is working again! the carrage stops the light dims then flashes and stays that wayi guessed that that is were the sensor reads for the white stripe (or home position) extra cleaning resets etc the light shifts >slightly (1" or so) to the left upon powering up and then goes back to >the far right and makes the noise > > >doug dornbos >for a navigate here

by whirlybird on Jan 25, 2006 at 8:40am Add comment Please sign in to comment 0 Thank you. Yes No Cancel Update (+2 points) 42 more comments Showalter Nov 07, 2007 Noise and stuck head problem, and notify you when a new solution is offered. Searching the WEB I found this link and it was very helpful. I get an error message: scanner failure, turn power off then back on again. http://www.fixyourownprinter.com/posts/22386

Hp Officejet 6110 All In One Troubleshooting

Tried absolutely everything. Noise and stuck head problem, and notify you when a new solution is offered. And they shouldn’t for the price that they pay for this product.

Sometimes it will find the scanner, scan the photo then when I press Accept on the HP software I get the message about no connection to scanner or cannot find scanner... I couldn't believe that HP could not choose black paint that will permanently stick to plastic that it is painted on. I bought one for under $3. Hp Scanner Failure While the printer is Turned ON, unplug the power cord from the back of the printer.

So in the end the real problem was flaking black paint on the optic guide line. Hp Officejet 6110 All-in-one Scanner Failure it just says "initializing" and then the noise starts again. I got it back on the right position and need now to calibrate brobably the scanner unit. Sounds as if somethings stuck.Pleas...

Also clean the inside and outside of the scanner glass pane itself. 7) Refit all parts, using the technique described above, in reverse order. 8) Switch on printer. Hp Officejet 6110 All-in-one Printer Luckily, I didn't give up. When released the message stayed and unit still did not work. Get news about the products and tech you really care about.

Hp Officejet 6110 All-in-one Scanner Failure

I even cleaned the CCFL lookin thing.. http://resetprinters.com/three-types-of-resets-for-your-hp-officejet-6110/ I also get a noise which sounds like a little bitty machine gun. >the light on the scanner is stuck over on the right hand side and seems >to vibrate with Hp Officejet 6110 All In One Troubleshooting I wanted to add this little tidbit. Hp 6110 All In One Manual Your name or email address: Do you already have an account?

Power cycle the printer by unplugging the power cord with the printer turned off, waiting 30 seconds, then plugging the power cord back into the printer and turning the printer on.Step check over here Ben Myers, Jul 31, 2006 #2 Advertisements aussiblu Guest Seems it is a common problem see http://www.fixyourownprinter.com/forums/printer/22386 and the advice there: "Remove the scanner glass and clean the rod that the Lubricate it with a few drops of Tri-Flow, available in small squeeze bottles at cycle shops. Die Zähne, der Zahnräder, sind aber noch Ganz. Scanner Failure Unable To Copy Or Scan

Your step by step instuctions on how to get to the underneath was so helpful. So I would suggest that you try this before doing the whole WD40 thing. by Anonymous on Nov 20, 2007 at 4:47pm Add comment Please sign in to comment 0 We have had this prob for a while and I noticed it was heat sensitive. his comment is here saved me 200$ for a replacemant!

Learn more You're viewing YouTube in German. Jo-Anne Jun 24, 2008 Hello,Well another THANK YOU for sillygirl. Three mirrors sit on the left of the assembly - two full length mirrors and a shorter one.

A dirty or blurry scanner glass may cause a deficient scanning and copy quality." It has been amply proven by posts on this forum that copy quality it not the major

Then lift the upper unit with the glass panel and place it in the back standing up. 6. I quote "This document shows how to clean the scanner glass internal surface of some HP All-in-One products. by whirlybird on Jan 14, 2006 at 12:04pm Add comment Please sign in to comment 0 Whirlybird -How did you get the scanner carriage aprt to get at the mirrors to I'm sure people will not spend 4 hours like I did researching and then taking apart the printer to fix this problem.

On the glass I used a microfiber rag and hot water, then I wrung it out good. Do not attempt to lift as if there were hinges in the back. will keep you posted. +:) jocjohn Aug 11, 2008 I've had this AOI printer for about five years now and recently experienced the problem described in this posting. http://upintheaether.com/hp-officejet/hp-officejet-6110-error-421.php nothing helps > > >Sanford >I appreciate your efforts to troubleshoot the issue. > > >Sanford >May I have your Phone Number beginning with your area code so I can see

Posted on Sep 04, 2007 Helpful 0 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images James Mc nair Level 1: An clear carriage jam, and then press enter 1-sacanner failure. Afrter cleaning the glass from the inside and using the #+6 and then pluging it worked!thank you all for the instuctions It saved me money and distress:) by Revital on May AFTER POWER ON OF IT DISPLAY AGAIN AND AGAIN DHIRENZAVERI Jan 08, 2008 I HAVE HP OFFICEJET 7208 ALL-IN-ONE.

If the scanner mechanism is turned over there is a structure that has three optical ports, top and sides, with about 1/16" openings that sits over a cone shaped depression which Now they offer an "exchange at a discount". i'm going to pass. Unplug the printer. 2.

I turned power on & off (repeatedly), unplugged & plugged back in all connections, shut down & restarted system -- all to no avail. Thanks to all. I'm looking for verification that on a US model 6110xi this is normal -or not.Thanks ahead of time. The T10 worked perfectly.Thanks again! - BuyItAllOnline.com 0 No problem.

When removing the four screws and pulling off the keyboard face plate, you'll find tabs on the outer part of the glass lid facing towards you. Perform a semi-full reset on your Officejet 6110 by holding the button combination given below, while plugging in the power cord. I used superglue to reattach glass, cleaned everything again. by ajzahn on Jun 18, 2005 at 5:03am Add comment Please sign in to comment Miine had the ADF as well, but if you follow the instructions in this thread, you

I have turned the printer on and off, but nothing has happened.