Home > Hp Officejet > Hp 8100 Error Codes

Hp 8100 Error Codes

Contents

note: The carriage in your printer might not be in the center of the printer like the carriage shown in the following image. How to print a self-test report Load unused, plain, white paper into the paper tray. The product lights might flash and the carriage might move. Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA. 4. Check This Out

This page requires Javascript. Replace DC controller. Change the processor. 2200-PMM Allocation Error during MEBx Download Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM. Figure : Open the cartridge access door and the printer lid Confirm which cartridges are missing. my site

Hp Officejet Pro 8100 Printer Troubleshooting

Close the printer lid and the cartridge access door. Repeat these steps for other cartridges that you want to replace. Go to Contact HP to review available service options.

Reboot the computer. Replace the system board. If the product does not turn on by itself, press the Power button ( ) to turn it on. Hp Officejet Pro 8100 Reset After you remove a duplicate cartridge, insert the correct cartridge within a few minutes to avoid possible damage to the ink system.

These patterns will make up a two part code: Major – the category of the error Minor – the specific error within the category Number of long beeps/blinks Error category 1 Hp Officejet Pro 8100 Wireless Light Blinking Do not leave the printhead out of the printer for more than a few minutes. Use only one type of paper at a time. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bph07107 Provide feedback Please rate the information on this page to help us improve our content.

warning: Do not reach into the cartridge access area at this time. Hp Officejet Pro 8100 Flashing Wireless Light Unplug the power cord from the wall outlet. Thank you! For more information on loading paper, see Loading Plain Paper, Cards, Photo Paper, and Specialty Paper .

Hp Officejet Pro 8100 Wireless Light Blinking

Press the Power button to turn on the printer. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c02881923 Pull out tray 2 (if installed), and then remove any loose sheets of paper from the tray. Hp Officejet Pro 8100 Printer Troubleshooting Reconnect the power cord to the rear of the printer. Hp Officejet Pro 8100 Ink Lights Blinking Press the Power button to turn on the printer.

Check that PS1 is blocked by the latch flag. http://upintheaether.com/hp-officejet/hp-officejet-7210-error-codes.php Verify system fan(s) are working. Figure : Open the cartridge access door and the printer lid Disconnect the power cord from the rear of the printer. Step three: Print a self-test report Print a printer status report to make sure that the hardware functions correctly. Hp Officejet Pro 8100 Printhead Error

Loading paper correctly might prevent paper jams. Gently remove any jammed or torn paper from the exposed underside of the printer. Wait until the printer is idle and silent before proceeding. http://upintheaether.com/hp-officejet/hp-officejet-v40-error-codes.php Figure : Insert the cartridge into its color-coded slot caution: Do not lift the latch handle on the carriage to insert cartridges.

Remove any loose sheets of paper from the output tray. Hp Officejet Pro 8100 Factory Reset Step two: Check the cartridge access area with the carriage undocked Keep the printer turned on. Go to the HP SureSupply website.

Check connector for bent or missing pins.

Unplug the power cord from the wall outlet. Verify proper memory module type. 201-Memory Error RAM failure. If any torn pieces of paper remain inside the printer, more jams are likely to occur. Hp Officejet Pro 8100 Symbols Figure : Insert the cartridge into its color-coded slot caution: Do not lift the latch handle on the carriage to insert cartridges.

Replace Cable, DC Controller to H.V. Reseat the graphics card (if applicable). caution: HP recommends that you wait until you have a new cartridge available before removing the old cartridge. navigate here All cartridges must be seated correctly in the printhead assembly.

For more information on loading paper, see Loading Plain Paper, Cards, Photo Paper, and Specialty Paper . The carriage moves to the middle of the printer. For systems with integrated graphics, replace the system board. Unplug the power cord from the wall outlet.

In Computer Setup, set Advanced > Device Options > NIC PXE Option ROM Download to DISABLE to prevent PXE option ROM for the internal NIC from being downloaded during POST to Disconnect the power cord from any power strip or surge suppressor, and plug it directly into the wall outlet. Figure : Remove the duplexer Gently remove any jammed paper or pieces of torn paper from the rollers inside the product. Solution two: Make sure that there are no duplicate cartridges installed Follow these steps to make sure that there are no duplicate cartridges installed.

Figure : Do not touch the electrical contacts or nozzles on the printhead Grasp the printhead on both sides with the electrical contacts facing the rear of the printer, and then Step one: Remove the cartridges and the printhead Follow these steps to remove the cartridges and the printhead. Tray 2 only supports plain letter and A4 paper. Solution one: Insert any missing cartridges Follow these steps to insert any missing cartridges.

Disconnect the power cord from the rear of the printer. Replace optional I/O card. 43 OPT INTERFACE 1. Try rebooting the system. Replace the system board.

When an indicator shows low-ink levels, consider having a replacement cartridge available to avoid possible printing delays. Check paper pickup rollers. Close the printer lid and the cartridge access door.