Home > Hp Laserjet > Hp P3005n Memory Error

Hp P3005n Memory Error


by johntriumph on Oct 13, 2009 at 9:31am Add comment Please sign in to comment Yes, another person earlier said that his board was smoking somewhat after 5 min. HP will let a warranty center get paid to fix these under the service note. I even brought an LCD panel with no display back to life yesterday. by unknown on Jul 28, 2008 at 9:47am Add comment Please sign in to comment 0 Please see below. navigate here

Disconnect all interface cables. Thanks for your input. Turn on the device. This did not show up here until recently because it does not effect networked printers. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00764932

Hp P3005 Memory Error Replace Dimm

The thing with a chip like this is its impossible to hand solder it to the board, the connections are too close. by eric111 on Aug 15, 2012 at 9:20pm Add comment Please sign in to comment 0 In my business I have 3 HP P3005dn printers, 2 of which had failed in I'm wondering if maybe they are suffering from the same cold solder problems as the 610N and 615N JetDirect cards have.

by ANO31 on Oct 13, 2009 at 1:34pm Add comment Please sign in to comment I followed your instructions and the 2015 works perfectly.I tried the same technique with the 3005 PAPER PATH JAM FRONT DOOR alternates with For help press (HELP) A page is jammed in the paper path. No action necessary. Hp P3005 Cold Reset Close the rear door.

Thanks, Brian by Anonymous on Jun 26, 2008 at 6:38am Add comment Please sign in to comment 0 I have a P3005dn which jams every time you try to duplex. Hp Laserjet P3005 Memory These are repaired professionally using air which is why the oven works. Turn the device off and then on. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=1846088 by moe on Sep 2, 2009 at 9:23am Add comment Please sign in to comment 0 I have had a number of boards repaired by a professional shop.

These messages are not affected by the AUTO-CONTINUE setting. Hp Laserjet P3005 Hangs During Startup MANUALLY FEED alternates with To continue press (SELECT) Media is in tray 1, but the print job requires a specific type and size that is not currently available. If the message persists, contact HP Support. 40 EIO X BAD TRANSMISSION alternates with To continue press (SELECT) A connection with the card in the EIO slot has broken. They all meant that I have to pay for the new board.

Hp Laserjet P3005 Memory

by frieste on May 7, 2008 at 1:40pm Add comment Please sign in to comment -1 Again, I appreciate your concern, but I am not an idiot. http://www.fixyourownprinter.com/forums/laser/55786 almost scared to depend on it and have been printing on the local inkjet for small jobs. Hp P3005 Memory Error Replace Dimm I have a fresh corpse with no display. P3005 Formatter Board So I called a local warranty center & luckily the guy knew how to look up service notes & said the note is DOC #C01215806 but my printer did not fall

STANDARD TOP BIN FULL alternates with Remove all paper from bin The output bin is full. http://upintheaether.com/hp-laserjet/hp-m1522-memory-low-error.php If CLEARABLE WARNINGS is set to JOB on the device CONFIGURE DEVICE menu, the next print job clears these messages. Some warning messages are clearable. If the message persists, contact HP Support. Hp Laserjet P3005 Replace Dimm 1

This is not a service, this is only shit. by johntriumph on Feb 15, 2008 at 3:11am Add comment Please sign in to comment 0 Heres a Pic I found, the chip is covered by a label (which may look Press (SELECT) to continue or press (HELP) for more information. his comment is here No action necessary.

Or if you need year-round support, you can choose our all-inclusive HP LaserJet P3005 annual maintenance agreement.

Common HP LaserJet P3005 (Q7812A) Error Codes & Problems HP Error Code:10 - Supplies Install A Supported Memory Dimm. To remove this message from the display, press (SELECT). Ensure that all trays are configured correctly before printing again. 41.5 UNEXPECTED TYPE IN TRAY X alternates with LOAD TRAY X The device senses a different media type than what is

Press (HELP) for help.

not worth mucking around. Lift the metal flap, and then remove any media remaining. Let me know how you get on haelge . Hp Laserjet P3005 Troubleshooting Call for Assistance 877-755-5300 Home About Us Contact Us Search Site Map Printers Supplies Accessories Parts Error Codes Login Shopping Cart Return Policy Privacy Policy Orion Printers and Parts 6030 Marshalee

If the message persists, contact HP support. 55.XX.YY DC CONTROLLER ERROR alternates with To continue turn off then on The engine is not communicating with the formatter. The device can print with this supply, but print quality might be affected. Even better still i can use a heat gun.I do not think it will work because the chip is a samsungchip on later boards. weblink View solution in context Reply 0 0 Gabe12 Tutor Posts: 13 Member Since: ‎01-09-2012 Message 2 of 4 (2,514 Views) Report Inappropriate Content Re: Supply memory error Options Mark as New

If the message reappears, there might be a problem with the software program. No amount of resetting or retrying made any difference. The board was set with the memory module removed, chip side up on these four balls in a baking pan.I put the pan in the oven for EXACTLY 8 minutes. I confirmed it 100\% !!!!But the bad news is HP will only give the extended warranty to the serial number range which is listed in a post somewhere on this site;

The device returns to the Ready state after the cleaning page is printed.