Home > Hp Laserjet > Hp P2015 Jam Error Light

Hp P2015 Jam Error Light

Contents

Be sure to preheat for at least 20 minutes.Thanks a million! on May 31, 2012 at 5:17 PM thanks.. It actually worked! Raidr 62,069 views 10:11 How to refill HP LaserjetPro P1102 Printer with CE651A cartridges - Duration: 9:47. navigate here

on May 11, 2011 at 11:06 AM Hi I do the formart card old i dont have the two leds in orange, pass correctly,but dont print any page the botton GO keep on trucking... Shake off the cover, Back the board... Turn off the printer. 2. Get More Information

Hp Laserjet P2015 Error Lights

Brett said... Liz said... I suspect that's verification of the suspicion that many people have that a lot of these boards have failed. Brett said...

Thank you fixyourownprinter forum! Thanks for the great info. There's still a lot of the older ones out there for sale. Hp Laserjet P2015 Manual Men its very disapointing to see how clients r spending so much cash yet the products we get this days r not reliable.

I have 12 of these printers for my business. Hp Laserjet P2015 Paper Jam Light Blinking Loading... Release the Go button.To do an NVRAM Reset:CAUTION Only perform the following procedure if absolutely necessary. http://www.printertechs.com/printer-troubleshooting/404-paper-jam-error-light-and-toner-error-light-hp-laserjet-p2015 The paper jam and toner lights on solid but nobody home.

Thanks to everyone for their input and especially the guys who shared their tips on the board cooking method!! Hp Printer Symbols What Do They Mean I don't have anything to lose... - Anonymous You were pretty lucky this worked. 350 deg F is nowhere near hot enough to melt solder. Once it starts, the printer will slowly feed some paper through, then it'll return to the ready state. I talked briefly with someone online about the problem but got no reasonable response.How much are the formatter boards?

Hp Laserjet P2015 Paper Jam Light Blinking

I'm assuming the board is what I see when I open the little 3x5 inch hatch in the center of the left side of the machine. http://www.laserpros.com/tech_tip_P2015.asp Unfortunately,it seems all of HP's recent models have issues. Hp Laserjet P2015 Error Lights I am in touch with a few of the HP CE's and have sent an inquiry into this issue. Hp Laserjet P2015 Attention Light Blinking See if this fixed the problem.

The technician will undoubtably tell you that your only options are to pay to send back your printer, or pay them to mail you one. check over here WiMan said... Kai Gillmann said... I was able to connect to the web admin interface and everything appears to be working properly. Hp Laserjet P2015 All Lights On Except Paper

on November 18, 2011 at 6:31 PM @Kris:You rule! Thanks for saving us some $. If this doesn't work, just send this thing to a recycling facility and get a stable printer. his comment is here baking remove it GENTLY.

on February 2, 2011 at 7:30 AM If your baking other formatters I suggest removing the battery if installed, these can't take the temperature. Hp Laserjet P2015 Troubleshooting If the formatter board doesn't work. on January 15, 2011 at 11:24 AM Whoa, this was one 'hot' tip!

They are back ordered to mid-Septemeber at this point.

Firmware has been on the hp site in over 1 year so I do not know where you got your firmware but you are just out of luck. This one never finished booting. Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Hp Laserjet P2015 Jam And Toner Light On Once liquid, the open circuit should close and stay closed after it cools; the board will function normally again.

This is amazing! The situation looked like this: I kept trying to find the jam, opening covers and powering it on and off. Thanks a million! weblink Turn the printer off.2.

I was a bit skeptical, since I know my Weller soldering station uses much higher temperatures, but I tried baking at 400 deg. Sincerely,CHRISTIAN ZETTERSTROMComplaint AnalystConsumer Protection Division(253) 593-2906I will keep this updated as much as I can.Rob S by Rob S on Aug 21, 2009 at 2:25pm Add comment Please sign in to Not sure if something happened when I moved it to my new home, but since my move (late December) I've experienced the same problems described above. (Also, I've had the printer Sign in to report inappropriate content.

on March 19, 2011 at 4:33 PM How do you want your PCB ? Thanks to all of you who helped keep this printer from becoming a boat anchor and no thanks to HP for your lack of help! Performing anNVRAM initialization resets some parameters that cannot be restored later.NVRAM initialization sets all default variables stored in NVRAM back to factory default values or to adefault ROM value, depending on I've had the printer for 17 months and it was a real workhorse until 2 weeks ago.

If you really want to keep it alive you're better off reflowing the old board. I used 350 degrees for eight minutes, propping the board up on 4 small aluminum foil balls to keep the board off the cookie sheet. - Anonymous I had nothing to You may put them back afterwards. 4. Start by unplugging the cables, carefully.

Anyway, baked mine yesterday and it works like a champ today. Thanks alot. Hopefully this printer will stay good for years to come. by unknown on Feb 3, 2009 at 1:00am Add comment Please sign in to comment 0 I've replaced my formatter board and so far, so good.