Home > Hp Laserjet > Hp Lj4250 Error

Hp Lj4250 Error

Contents

Only one copy will be produced. Turn the printer power off. REINSERT DUPLEXER The duplexer has been removed. Remove any jammed paper from the stapler/stacker.

NON HP SUPPLY INSTALLED Economode disabled The printer has detected that the print cartridge is not a genuine HP supply. WARNING: The fuser may be very hot; ensure that the fuser is allowed to cool for at least 30 minutes before touching. Turn the printer power off and then on. If loose toner falls into the printer, it might cause temporary problems with print quality.

Hp Laserjet 4250n 49.4c02 Service Error

Unable to mopy job alternates with Memory or file system failures would not allow a mopy job to occur. Do apprciate any help prior to the morning job. The message shows the most likely type and size available and the tray in which they are available.

CAUTION: Static electricity can damage DIMMs. top Handling persistent messages If a message persists requesting that a tray be loaded, or if a message indicates that a previous print job is still in the printer memory, press NON HP SUPPLY INSTALLED For help press Product illustration The printer has detected that the print cartridge is not a genuine HP supply. Hp Laserjet 4250 Network Setup If the message persists after all jams have been cleared, a sensor might be stuck or broken.

This is the default setting. Hp Laserjet 4250 Error Codes I've had trap stops(the slider at back of tray) cause this these problems when they get broken. Correct the error and then try again to store the job. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422 Turn the printer power off.

top Additional information To print a configuration page at the control panel Press (Select) to open the menus. Hp 4250 Firmware Turn the printer power off and then on. Once you have the fuser out, check the fuser's barcode label for the part # and see if the part # matches with your model printer. Correct the error and then try again to store the job.

Hp Laserjet 4250 Error Codes

Replace the staple cartridge.. Using the printer online Help system This printer features an online Help system on the control panel that provides instructions for resolving most printer errors. Hp Laserjet 4250n 49.4c02 Service Error Turn the printer power off and then on. Hp Laserjet 4250 Troubleshooting DUPLEXER ERROR REMOVE DUPLEXER Install duplexer with power off The optional duplexer has an error.

Try printing a job from a different program. Fusers are a consumable part and are sold as part of a maintenance kit; it is expected over the life of the printer you will replace the fuser several times. Press Product illustration (Select button) to clear the error message and continue printing. 41.X ERROR For help press Product illustration alternates with 41.X ERROR To continue press Product illustration A temporary Try printing again to an existing folder. Hp Laserjet 4200 Error Codes

X Description 0- Scanner error 1- Scanner startup error 2- Scanner rotation error Action Press the (Select) button to continue. part# RM1-0013  purchase HP 4200 fuser/maintenance kit here for use in HP LaserJet 4200, HP LaserJet 4200N, HP LaserJet 4200TN, HP LaserJet 4200DTN, HP LaserJet 4200DTNs, HP LaserJet 4200DTNsl part# RM1-1082    Turn the printer power off and then on. Action Press the (Select) button to resume printing.

Remove the print cartridge and check the paper path for paper. Hp Laserjet 4200 Cartridge Installed Message Check that all of the cables are connected to the HP Jetdirect card and that the HP Jetdirect card is seated properly. top 13.06 and 13.12 JAM INSIDE REAR DOOR Description Paper jam inside or outside the rear door of the printer.

This error can occur if the driver you are using is not IEEE-1284 compliant.

If the above action does not solve the issue, contact HP or authorized service provider. top 13.98.00 OPEN INPUT TRAYS THEN OPEN AND CLOSE TOP COVER Description The rear output bin was opened when the printer was attempting to send a page to the duplexer, a If the message persists, contact an HP-authorized service or support provider. 79.XXXX ERROR To continue turn off then on The printer detected a critical hardware error. Hp Laserjet 4250 Cleaning Page If STAPLES OUT=CONTINUE, printing continues, but the job is not stapled.

This message is displayed until you install an HP cartridge or press the override button Product illustration (Select button). Make sure that the accessory is properly seated on and connected to the printer, without any gaps between the printer and the accessory. Set size and type to a specific setting if printing with only one type of paper. Please wait while we process your request.

I also had the annoying and scary clunking sound on loading the tray. Any printer repair required as a result of using non-HP supplies or unauthorized supplies is not covered under the printer warranty. Print a Configuration page and verify that the tray settings match the media in the tray. Plug the printer into a wall outlet and see if this resolves the problem.

This is typically an e-label issue. Figure 9: Removing the jammed paper Make sure that the paper is flat in the tray at all four corners and below the maximum-height indicators. Remove all non-HP paper-handling devices. alternates with 41.3 LOAD TRAY XX: [Type] [SIZE] For help press ? 41.X PRINTER ERROR For help press ?

top 59.4 EP MOTOR ROTATION ERROR (HP LaserJet 4300 only) Description The print-cartridge drive motor (HP LaserJet 4300 only) is not functioning properly. Use (Up Arrow) or (Down Arrow) to scroll to INFORMATION, and then press (Select). If the error does not clear, turn printer off then on. top 13.XX.YY.DUPLEX JOB INTERRUPTED Description There was an error while the printer was duplexing.

part# RM1-0013 purchase HP 4200 fuser/maintenance kit here for use in HP LaserJet 4200, HP LaserJet 4200N, HP LaserJet 4200TN, HP LaserJet 4200DTN, HP LaserJet 4200DTNs, HP LaserJet 4200DTNsl part# RM1-1082 The document, Interpreting control-panel messages , lists the most common messages that require attention or that might raise questions. Figure 7: Reinstalling the print cartridge and closing the top cover If a jam message persists, there is still jammed paper in the printer. Push the fuser firmly--listen for the sound of both blue levers clicking into place.

Figure 11: Sliding tray back into the printer Open and close the top cover to clear the jam message. alternates with 68.X PERMENANT STORAGE ERROR To continue press (Select) Description One or more printer settings that were saved in the nonvolatile storage device are invalid and have been reset to ROM DISK NOT INITIALIZED To clear press Product illustration alternates with The file system has not been initialized. If the message persists, contact an HP-authorized service or support provider 11.01 = Dead clock battery 11.02 = Dead real-time clock This message is displayed when there is a problem with

Turn the printer power off, and then replace the DIMM that caused the error. 54.XX ERROR To continue turn off then on This message is typically related to a sensor issue. Click here to contact HP Support . Does it print OK?