Home > Hp Laserjet > Hp Lj P3005n Dimm Error

Hp Lj P3005n Dimm Error

Contents

The printer will work fine all day, but first thing in the morning the printer is froze up. To exit, press (HELP) 59.XY ERROR alternates with To continue turn off then on A device motor error has occurred. by abel (3/29/09 6:46 PM) reply + / -Ive got same problem here,my NEW-(not more than 4 month old)-HP LJ 3005n--by today did not show anythings on its LCD (blank).When I What the hell, I thought, they're dead anyway -- so last night I took out the formatter boards, preheated the oven to 350F and baked the boards for 8 minutes on navigate here

Whenever the device is ready, not busy, and has no pending warning messages, the status message Ready appears if the device is online. by dmzcompute on Jun 25, 2008 at 7:57pm Add comment Please sign in to comment 0 Yep, it will be the formatter. If it is saying DIMM 1 then I'd try replacing the memory stick first. This area should list the new device language. More hints

Hp Laserjet P3005 Memory

When I did this I took the precaution of desoldering them from the board, doing the baking, and resoldering them (make sure you pay close attention to the polarity on the Lift the metal flap, and then remove any media remaining. Do not turn off the device. Maybe next time I spend $900 I'll buy Lexmark or Okidata???

Press (DOWN) to see step-by-step information. Sorry for this long story but it may be worth $300 to someone else. All Rights Reserved. Hp Laserjet P3005 Hangs During Startup I have 3 items from HP identifying this and similar problems due to a bad Toshiba chip on the formatter board.

only printed 3,700 pages. P3005 Formatter Board The paper stops just before the sensor in the fuser.Anyone got any ideas?. by cscotech on Apr 7, 2008 at 10:12am Add comment Please sign in to comment 0 Well from your earlier post your serial # does fall within the list covered by http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00765016 Reinstall the firmware.

If the message persists, contact HP Support. 40 EMBEDDED I/O BAD TRANSMISSION alternates with To continue press (SELECT) The connection with the HP Jetdirect embedded print server has broken. Install A Supported Memory Dimm. I am wondering if I should just send a formatter? My P3005 worked for 5 days after the blow drier fix & then went back to memory errors & a blank display, etc. by frieste on May 16, 2008 at 8:19am Add comment Please sign in to comment 0 you know all were saying to you is, if you dont what your doing then

P3005 Formatter Board

im selling my HP for 300 eur, 1 year old :) by unknown on Oct 16, 2009 at 3:33pm Add comment Please sign in to comment 0 None of the connectors I had the same problems as most of you and followed the advice on contacting HP and quoting the service note. Hp Laserjet P3005 Memory Check the DIMM Installation. Hp Laserjet P3005 Replace Dimm 1 The one that your network/USB cable plugs into.

You would be wasteing your time.The board needs to be replaced.FORMATTER BOARD Pn Q7848-61004 by johntriumph on Dec 22, 2008 at 10:19am Add comment Please sign in to comment 0 what check over here The only thing I have heard of is sometimes and I think only on the P2105 board there is a bit of tape used to cover some chips by the expansion Install supply alternates with For status press (SELECT) The print cartridge is missing. Open rear door, and then remove all media found. Hp P3005 Cold Reset

Also, no print tests from the control panel either. Wait for the process to complete. I thought the idea of putting the boards in an oven was a little extreme but then again what do you have to lose? http://upintheaether.com/hp-laserjet/hp-p3005n-memory-error.php Loading...Oops :Please try again.

by Anonymous on Feb 6, 2009 at 1:28pm Add comment Please sign in to comment 0 I'd keep the 8150DN...They are relatively cheap to maintain. Hp Laserjet P3005 Stuck On Initializing Occasionally printer will get to 'ready' but cannot be pinged or printed to. During this time, no jobs can be printed.

by frieste on May 7, 2008 at 1:40pm Add comment Please sign in to comment -1 Again, I appreciate your concern, but I am not an idiot.

If the message persists, replace the storage device. So, by far one of the most bizzare fix suggestions I've ran into, and also one of the most effective. There a song about this, M I C K E Y M O U S E. Hp P3005 Service Manual Yes No Cancel Update (+2 points) You can't post conmments that contain an email address. × Comment Anonymously Video Images 3 Answers Azrael SRL Level 3: An expert who has achieved

Dave L. by unknown on Nov 23, 2010 at 3:32am Add comment Please sign in to comment Rather than banging your head against the proverbial wall, it's a lot easier to just remove One was a new board with the larger memory board. weblink If you have not already done so, print a configuration page to find out how much memory is installed in the device before adding more memory.

It takes a special machine that solders all the connections at the same time. by johntriumph on Oct 14, 2009 at 6:13am Add comment Please sign in to comment 0 The professional board guy I have been dealing with is warning about melting the plastic ordered a new board. Service or repairs required as a result of using non-HP supplies are not covered under HP warranty.

Yeah, good luck with that choice. They know of the issue since approximately 25\% of the P3005 printers that shipped during that time frame had the bad chip. I kept the heat on & re-booted the printer again & the display then stayed black with no light at all & I thought well I am getting somewhere. Press (SELECT) to continue printing.

Somebody please try it and report back. No action necessary. USB STORAGE DEVICE FAILURE alternates with Ready To clear press (SELECT) The USB storage device has failed. CODE CRC ERROR An error has occurred during a firmware upgrade.

Install a supported DIMM. 54.XX ERROR A device command error has occurred. Make sure the media guides are adjusted correctly. Install a new cartridge. He said there is a problem with the formatter board and gave me also the part number of a new board.

There also seems to be a bit of discoloration around the large BGA chip, is this normal? If you have a powerful fan-forced oven I suggest eight minutes in there at 220 degrees Celsius. Printing can continue for jobs that do not require the RAM disk. Provide feedback Please rate the information on this page to help us improve our content.

The one I use puts out over 1200 degrees, but people have had success using ordinary hair dryers. One thing is certain, the one chip listed as causing this problem in HP service literature is not the problem, or at least not the only problem. If you want to replace you need a 200 pin DDR2 DIMM in either 32mb, 64mb, 128mb or 256mb value. Lift the metal flap, and then remove any media remaining.