Home > Hp Laserjet > Hp Laserjet Iip Error 12

Hp Laserjet Iip Error 12

Populating a Keyword field 3. Please email > a direct reply, thanks > -ty Top Error "12 OPEN OR NO EP" on HP LaserJet IIP, what the heck? Check the I/O connections and make sure the proper media is being used. San Rafael, CA Great that you have that part in stock and thank you for your quick reply. this contact form

Check registration area. Check the fan connector and make sure that the fan is not blocked. 2. Power cycle the printer. Any suggestion is appreciated even to hurling it out of the window. http://www.repairfaq.org/samnew/printfaq/pcfljiipec12.htm

Privacy Policy Terms of Use Sign Up Login Add Question dansitarz asked May 7, 2007 at 1:55pm 0 Unknown Printer HP LaserJet IIP-Error Code 12 I have a HP LaserJet IIP Added to that, this article will allow you to diagnose any common error alerts associated with Hp Laserjet Iip Error 12 error code you may be sent. On the 4V/4MV check the toner cartridge micro switch on the High Voltage PCB - SW501.

If the software tells the printer to expect a different size (legal, A4, COM10) than the tray available, you will get an error. Can also indicate a mis feed or paper not being picked up. Replace fuser. Often it is advisable to just replace an older printer. 02 Warming Up (If longer than 3 minutes); also see error code 50. 2686A/D Replace DC power supply/Main motor driver assembly.

XX Description 00 memory error on the cartridge or 01 memory device not found 10.00.00 Black print cartridge 10.00.01 Cyan print cartridge 10.00.02 Magenta print cartridge 10.00.03 Yellow print cartridge Supplies Remove the card and reseat it, try swapping with a know good card from another printer. Back back to top How did we do? http://www.fixyourownprinter.com/posts/17166 Bad local power.

If that's not it, then take off the bottom cover from the printer and stand the printer on one side. If you want to go for a newer printer, I personally would go for a Laserjet 1200. If you click on the Repair Kit Page on the left task bar, you'll find a 12 door open kit for your problem. The Hp Laserjet Iip Error 12 error message is the Hexadecimal data format of the error message generated.

Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again. You can depress these by hand and hear them click. Back back to top How did we do? As I said, it _might_ use the toner cartridge switches to detect when the cover is closed.

Incorrect cable hookup or bad I/O port in computer. weblink Back Error 11 - Paper Out Paper tray empty or not seated correctly. Raymond Connect-It Top 1. Defective toner cartridge in the Laserjet 4 Plus only.

In some instances, electrical noise in the cable can corrupt data during transmission to the printer. Please email a direct reply, thanks -ty 2. If you don't know what you are doing, you should contact one of them for assistance, maintenance and repair. http://upintheaether.com/hp-laserjet/hp-laserjet-error-64.php Works great and certainly solved the problem (as I expected it would). -Alan A.

Depending on the model, a firmware DIMM may need replacing or a flash update. Also you get this error if the fan is not working. (From: Dave Lee ([email protected]).) Most times I find that its the Density PCA that causes the problem. No toner cartridge.

Reseat DIMM, then Formatter - Replace or flash DIMM then formatter Back back to top How did we do?

Replace appropriate fan as needed. Short C202 on the DC controller PCB to bypass the 20 minute delay, power printer OFF!!) 4V, 4L, 4P, 5P Verify fuser is properly seated Replace fuser 51 Error (Loss of Check and replace same 68 Error / Service / Cold Reset All printers Temporary error. ERROR 41 Momentary error, press "Continue" or "GO" to reset the printer 5L/6L Power Cycle the printer if error continues reseat the DC controller to Formatter 5P/6P Occurs if printer picks

Also caused by the density adjusting PCA located behind the density adjusting slide switch. Moe will post the kit, no problems. Replace device which triggers error. http://upintheaether.com/hp-laserjet/hp-laserjet-error-52.php You can reseat the connectors to the scanner assembly and the control board.

LJ8100/8150 A fan motor failure occurred. I/O configuration for the computer or printer is incorrect. Could be a bad cable or loose connection or just a poor quality cable. and CSGNetwork.Com All Rights Reserved Home | Advertising | Calculators and Converters | Contact Us | Javascript | Sitemap | Glossary | Top Free Apps

If the problem continues, remove the optional interface card and set the printer for standard parallel interface by taking off-line and holding down "Menu" key for 5-10 seconds. This can generally get you 100 or so more pages. The capacitor on my printer went open-circuit big time! Joan Respond to this 0 Joan, the cause of your ERROR 12 message is that the Toner Density Board has gone bad.

Copyright © 1994-2007, Samuel M. Then put the printer back online and send a test job from the host computer via the parallel cable. Replace or clean as needed. Verify that the tabs aren't damaged and that the tray switches located in the printer are not damaged.

Improper MIO connection - look at pins on formatter MIO connection reseat card.