Home > Hp Laserjet > Hp Laserjet 9040 Error

Hp Laserjet 9040 Error

We have replaced the fuser, high voltage power supply, and DC controller. Figure 3: Opening the front door Check for paper in the duplex printing accessory area, and remove any paper by pulling it out of the printer. We fix Hewlett Packard 9000, 9040 and 9050 printer error code repair! I am curious and will continue until it is resolved. http://upintheaether.com/hp-laserjet/hp-laserjet-4l-error.php

Access through the left door. LaserJet 9000/9040/9050 40 EIO X BAD TRANSMISSION 40 A connection with the EIO card in slot X has been abnormally interrupted. by Anonymous on Aug 31, 2009 at 7:00am Add comment Please sign in to comment 0 Yeah I have a Hp 9040 laserjet printer that is giving this error also 49.4C02. Figure 1: The event log Interpret the event log Each individual entry in the log is called an “error,” while all errors occurring at the same page count are called an

Tested great. The last error is the error at the top of the event log printout with the highest number in the left-most column. The description or personality gives detail to the error messages. The retainer DC motor, located in the accumulator, is damaged.

If a stapler/stacker is attached, carefully pull out any paper that might be protruding from the accumulator area. Event log page Use the event log to diagnose and troubleshoot printer errors and intermittent failures. Turn the printer off. 2. It worked fine after DC controller was replaced and first time powering up.

i have problem in our printer HP 9040 MFP.Error code 49.4C02 this is the error code display in my control panel. I replaced the Paper Transfer Assy, with no success. This can occur due to a timing error or intermittent connection between the formatter and DC controller. top Checking the duplexer area for stuck paper Open the left door and carefully pull out any paper from area (see Figure 1).

that cause error 13.20. It is a consumable item, pricey but consumbable. There is a door latch switch that can get stuck. Toaccept touch “OK”.To change touch NEXT.

We also replaced all network cables and switched it to another port on the switch and it still continues. http://www.laserprinterservices.com/hp9000errorcodes.html Using the product Help system This product features a Help system on the control panel that provides instructions for resolving most product errors. For information about cleaning the printer, see the Introduce Guide on the product CD, or use the link provided below to contact HP. Perform a paper path test to isolate the problem .

Close the tray. http://upintheaether.com/hp-laserjet/hp-laserjet-error-58-3.php Have a nice day!!! Media is activating the exit sensor when the printer is turned on. Error code 13.12.00 JAM INSIDE LEFT DOOR 13.12.00 a page is jammed in the paper path at the duplexer.

Error code13.12.23 JAM IN LEFT ACCESSORY 13.12.17 Media is jammed in the accumulator exit area. Recommended action Touch Continue to get to TRAY xx SIZE=. Push the output device back into place (Figure 15). navigate here FF04 Service Error on a 9040N.

Observe any error trends. (For example, do jams tend to occur in a specific area of the printer?) Record any specific error trends. the acuator switch for the front door and the back door are the same switch located inside left door up front. If the error message has not cleared, turn the printer off, unplug the output device, then disconnect the output device from the printer.

Open and close the front door to clear the message.

Wird geladen... Reconnect the cables and power cord. Turn the printer on. 4. To exit the Help system, press the ?

NOTE: HP Web Jetadmin does have capabilities to override paper types and sizes and certain conditions. Open the front door (see Figure 3). Where does the leading edge of the first sheet of paper in the printer's paper path stop when a jam occurs? his comment is here An improper communications protocol might be in use.

top 68.x PERMANENT STORAGE ERROR alternates with CONTINUE Explanation An error occurred in the product nonvolatile memory (NVRAM), and one or more product settings has been reset to its original factory XX = 04 - 58.04 error (power supply) XX = 03 - 58.03 error (CPU) HP LaserJet 9000/9040/9050 59.X A printer error occurred, and X corresponds to the following issue: Error WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... and may not be used without advance written permission of PrinterTechs.com, Inc.

A pickup delay jam has occurred. If this message appears often, simplify the print job. Do you wish to proceed to the home page of the new product? Figure 6: Opening the right door Check for paper in the right door area, and remove any paper from this area.

by ezra.mwelwa on Jun 14, 2013 at 2:51am Add comment Please sign in to comment 0 9040 printer is giving me error code 13.20 paper jam inside right door.I have tried Reinstall the paper trays. Remove the staple cartridge (Figure 47). Recommended action Turn the product off, and then turn the product back on.

Because the guides get misaligned, the paper going through the paper path may be slightly misaligned or skewed. Tray 2: The media did not reach the tray 2 feed sensor (PS1402) within the specified time. Figure 2: Example of events 1 - The event appears on display panel 2 - The error number appears in the event log 3 - The error code appears in the Not all messages are listed, because some (such as READY) are self-explanatory.

Use the event log page and event log codes to aid in isolating where the errors are occurring. Media is present in the printer. by Anonymous on Jul 21, 2005 at 1:30am Add comment Please sign in to comment 0 Problem: 13.20.00 Jam inside left door. Figure 5: Lifting the green tab in the jam access area Remove any paper from this area by pulling it out of the printer.

Not ALL of them, just certain jobs. Replacing the jet direct card solved the problem.