Home > Hp Laserjet > Hp Laserjet 8150n Error Messages

Hp Laserjet 8150n Error Messages

On the Laserjet 4/4+ an error 12 can indicate the top cover open or a broken tab on the cover assembly. Take a sharp tool, like a razor blade and scrape the buildup off these edges. You might have attempted an illegal operation, such as trying to download a file to a nonexistent directory. Check the HP paper specification guide for more info. his comment is here

Can also be formatter PCA. Press GO. Check for opens on the cable. If it comes up ready then ... http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=27718

Remove the Formatter PCA 2. The line voltage and current source at the printer location might need to be inspected to ensure that they meet the electrical specifications for the printer. Try swapping the card into slot 1 or 2. You can verify this by substituting a known good DC controller if possible.

May be feed problem. By using this site, you accept the Terms of Use and Rules of Participation Sign Up Login Add Question unknown asked Mar 7, 2007 at 5:25am 0 HP LaserJet 8150 X Description 2 Fan 3 - Formatter Fan (intake) 3 Fan 2 - Laser/scanner (exhaust) 5 Fan 1 -Low-voltage power supply (exhaust) 6 Fan 4 - Face-down delivery (exhaust) 9 Fan this is a network card error.

BAD DUPLEXER CONNECTION The duplexer is not connected properly. Sensor Arm Stuck or Broken - check for free movement of the sensor arm. HP LaserJet 8150 series 8150n, 8150dn models of printer repair and Maintenance service in Southern California! http://www.fixyourownprinter.com/posts/45741 Check the MIO card, remove, clean contacts, reinstall.

Check and reinstall. Your cache administrator is webmaster. Or just drag it here! If the firmware should become corrupted or fail (usually because of an interruption when attempting to update the firmware), the product will no longer function.

what do i need to do to correct this error?? If the error continues: 1. Replace as needed IIP S/N between 2925J00000 and 3047J99999 replace fuser assembly Back back to top How did we do? Make sure that control panel setting for Tray 1 or the envelope feeder is correctly adjusted for size. (The printer will continue trying to print the job until size settings are

Make sure that the envelope size and type are set correctly from the Paper Handling Menu in the printer's control panel. this content ERROR 14 No EP Cartridge or No Toner Cartridge No toner cartridge or cartridge not fully seated - pull it out and install it again. Turn printer off, unplug it and reseat the formatter board. Press the spring contacts and listen for the micro switches.

IIISi/4Si check the door open sensor flag, PS1. Add memory to printer or reduce complexity of print job On the 5P turn the image adapt and page protect to ON or AUTO. Back back to top How did we do? weblink In this case, a firmware recovery DIMM is available.

EIO DISK INITIALIZING The disk accessory card takes a long time to initialize. I will have purchasing call in an order. Press to resume printing.

If you get the same error then you will need to replace the card Question about HP LaserJet Printers & Copiers 1 Answer Error code 40.0 EIO slot X has been

ERROR 41-X X= 1,2,4,5 A temporary error occured - Press "CONTINUE" to clear. 41.3 Error - Unexpected paper size - more than one sheet of paper picked up. Check the connectors on the DC controller and power supply. X = Description 4 Printer Fan 7 Duplex Fan 1. Remove the card and reseat it, try swapping with a know good card from another printer.

Error 18 MIO Not Ready The printer is not connected to a LAN when it's expecting to see a LAN. Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants. check over here by davelh on Feb 10, 2011 at 1:27pm Add comment Please sign in to comment 0 I've done everything you say above but I still have the message.

Improper MIO connection - look at pins on formatter MIO connection reseat card. Print the job using a driver for a different printer language or add the requested language to the printer (if available).