Home > Hp Laserjet > Hp Laserjet 5m 53.12.03 Error

Hp Laserjet 5m 53.12.03 Error

Short the pin closest to the front of the printer. (The printer must be turned off.) II, IID, III, IIID Only: 1. If the fuser does not turn on check SW101. 3. Values of X, Y, and ZZ are as follows: X = DIMM type 0 = ROM 1 = RAM Y = Device location 0 = internal memory (ROM or RAM) 1 Broken separation belt. 2. his comment is here

This problem can be caused by software/drivers, memory PCA's, font macro personality cartridges, or optional I/O cards. 2. HP LaserJet Error Codes and Service errors Back For additional help please Email our technical department Choose the error number from the menu below 02 11 12 12.x 13 13.x 14 The DIMM that caused the error will not be used. Temporary printer error, check printer's configuration. 57 ERROR II, IIID Only: 1. 57-1 Error - Incompatible memory card in front slot. 2. 57-2 Error - Incompatible memory card in rear slot. http://arstechnica.com/civis/viewtopic.php?t=653421

Defective Paper Control PCA on the Paper Feed Assembly. 4L Only: 1. by Anonymous on Oct 18, 2009 at 4:04pm Add comment Please sign in to comment 0 I had the same problem, removed the RAM and put it in another slot. The system returned: (22) Invalid argument The remote host or network may be down. DC Power Supply malfunction. 2686 Only: 1.

Check that PS1 is blocked by the latch flag. Bad laser unit or improper laser power setting. 2. You will be able to vote what to add next as your priority! 3. Bad cassette microswitch. 2.

Replace Laser/Scanner Assembly. 3. Replace Main Motor PCA or Main Motor. 4. IID, IIID Only: 1. DC Controller malfunction. 4.

Replace Parallel interface 5. I/O card is unable to accept data or is not connected to the network. 30 PS ERROR XX 1. Remove I/O cables. (Cable is hooked up incorrectly or bad interface in computer.) 2. c.

Replace Formatter PCA. 64 error 4000/4050/4100/5000/8000/8100 only: A scan buffer occurred - if it persists replace formatter. 66.xx.yy error 4000/4050/4100/5000 only: An error occurred in an external paper handling device, stapler/stacker. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=74341 inscrivez-vous, c'est gratuit et ça prend moins d'une minute ! See Service Note 33471-01B if Serial No. IIP, IIP+, IIIP Only: 1.

S'inscrire maintenant Vous n'êtes pas encore membre ? this content Check PS102 and PS103 13.5 Paper delay jam at fuser. Replace Interface/Formatter PCA. Check Fan 2, replace if necessary. 57.4 ERROR 1.

Warranty status:Unspecified Check warranty status Enter product serial number The serial number you entered,, matches a different product than the current product. Disassemble clutch and re-grease. I've seen a couple of printers where the jet direct card caused the whole printer to go dead after less than a second of operation. http://upintheaether.com/hp-laserjet/hp-laserjet-error-64.php This product has been successfully added to your profile.

Check connector J7 on DC Controller and connector at Fan 2. 2. Check paper feed roller. Summary rating? 3.0 out of 5 based on 1 Retrevo review Based on the facts above, Retrevo's recommendation is: Average Buy for Everyone Check Prices »

READ FULL ARTICLE » Hp 4si | Compare Prices, Reviews and Buy at Nextag Hp 4si - 131 results from HP, MAGNAFLOW, Premium Compatibles like HP Laserjet 4si 3si Maintenance

Signaler baladur13 28499Messages postés mercredi 11 avril 2007Date d'inscription ContributeurStatut 17 octobre 2016 Dernière intervention - 29 janv. 2009 à 09:12 Cela veut dire que dans ton imprimante une mémoire est Laser Malfunction See Error 51. 53.XY.ZZ Memory Error Cycle Power. I have two new C3147A-ALC double sided sticks from AllComponents and AllComponents tells me this is the correct memory for the HP 5Si. Replace optional I/O card. 43 OPT INTERFACE 1.

Replace formatter PCA. 60, 61, 63 MEMORY ERROR IIISi/4Si Only: 1. Sensor arm stuck or broken. 12 PRINTER OPEN 1. The product could not be added to your profile at this time. http://upintheaether.com/hp-laserjet/hp-laserjet-error-52.php Simplify print job. 2.

IIISi/4Si Only: 1. WHen the jet direct card is plugged in, i get that error, however when the jet direct is not installed, everything works fine.Dan by unknown on Jan 13, 2002 at 8:02am Replace cable, Fuser to DC Controller, connector J206. (P/N RG1-0907-000.) 2. Replace toner cartridge. 2.

Inspect Fiber-Optic Cable between Laser/Scanning Assembly and DC Controller. 3. Check paper pickup rollers. Replace high-voltage Power Supply. The ram is fully loaded, 26MiB.What should I do?

by moe on Jan 12, 2002 at 10:56pm Add comment Please sign in to comment 0 Its weird though. Trying to print envelope in duplex mode (envelopes cannot be duplexed). Replace Formatter PCA. 79 SERVICE (Document Error) 1. Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.) IIP, IIP+, IIIP Only: 1.

Vimow Updates 1. Note II: Short C211 on the DC Controller to bypass Error 50 time delay. (The printer must be turned off.) Note IID: Short C216 on the DC Controller to bypass error What happens is you do not use slot 1?