Home > Hp Laserjet > Hp Laserjet 4350 Error Codes

Hp Laserjet 4350 Error Codes

Contents

If you have any questions give us a call toll-free 866-352-7108 or local 608-831-2396, we can help you get the right fuser for your specific model. Table 7-7 Numerical printer messages (continued) 356 7 Troubleshooting Control panel message Description Recommended action 50.X FUSER ERROR For help press A fuser error has occurred. I have also checked the groundings and i think its ok. Turn the printer power off and then on. navigate here

Reconfigure the size in a tray so that the printer will use a tray that contains the size required for the print job. One screw holding it and you just scrape off the gooey sticky stuff under the spring loaded plate. A jam exists in the staple cartridge (the stapler did not finish stapling but was able to return to its home position). 1 Press ( HELP button for detailed information. 2 If you still have issues which I suspect you will the fuser probably has an issue. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=412160

Hp Laserjet 4250 Cleaning Page

Printing can continue, but behave unexpected in response to the changed settings. Try printing again to an existing folder. by dmzcompute on Oct 26, 2011 at 6:18pm Add comment Please sign in to comment 0 Thanks, dmzcompute, you were right on!

If the other scanner assembly solves your problem then I suggest to check your scanner assembly but please be very careful when opening it. The toner has been replaced with a new original one, which the fuser also has been. by dmzcompute on Oct 25, 2014 at 6:56pm Add comment Please sign in to comment 0 Hi there. Hp 4350 Maintenance Kit Also what toner are you using.

It paper you can sometimes use a stiff folder feeding it up the channel from below to force out the paper. Hp Laserjet 4250 Error Codes The DIMM may need to be replaced. The printer was set to continue printing when a supply needs to be ordered. https://www.laserzone123.com/u4350generalcodes.php I found that the deflector actuating arm in the top cover was missing.

HP 4350 ERROR 68.X PERMANENT STORAGE FULL A nonvolatile storage device is full. Hp 4250 Driver After performing the actions above, procede with the following: 1 Turn the printer on. 2 If the error message disappears, reinstall each DIMM and EIO device individually, making sure to turn Turn the printer power off and then on. Re-install the plastic rear output bin.

Hp Laserjet 4250 Error Codes

Rangel by unknown on Oct 17, 2012 at 11:13am Add comment Please sign in to comment 0 My HP 4350n is displaying - Waiting for Tray 2 to lift... LASERJET 4350 ERROR 58.X PRINTER ERROR A printer error has occurred where a memory tag central processing unit (CPU) error was detected, or there is a problem with the air sensor Hp Laserjet 4250 Cleaning Page Printing continues but the job is not stapled. Hp Laserjet 4250 Manual Check that the accessory is properly seated on and connected to the printer, without any gaps between the printer and the accessory.

If the message persists, contact an HP-authorized service or support provider. 59.XY ERROR For help press Product illustration alternates with 59.XY ERROR To continue turn off then on A temporary printing check over here If the error reappears, record the message and contact an HP-authorized service or support provider 68.X PERMANENT STORAGE WRITE FAIL To continue press Product illustration The storage device is failing to The original poster seemed to suffer from using bad remanufactured toner cartridges, so the solution involving fuser stuff wasn't mentioned.We tried the half test on our HP LJ 4350 and the Then checked the printer top cover to see what the solenoid actuating arm contacted. Hp 4250 Service Manual

Just remove the cables you can at the laser/scanner, remove the 4 screws that secure the assembly to the frame. To add additional memory, Up to 512 MB RAM via two industry-standard 100-pin DDR DIMM slots HP LaserJet 4350n The HP LaserJet 4350n printer includes the following features of the HP If i kinda push the paper while it is feeding into to print it will go right through but nothing will print??? http://upintheaether.com/hp-laserjet/hp-4350-502-2-error.php More memory may help.

HP Jet direct 620n internal enhanced input/output (EIO) print server 3. A 13.20.00 error message indicates that the printer power was turned on or that the printer attempted to initialize while the prefeed sensor (PS102), the top-of-page sensor (PS103) or the fuser TOO MANY PAGES IN JOB TO STAPLENOTE: The stapler/stacker LED iscontinuously illuminated in green (this errorapplies to the stapler/stacker only). 66.12.XXoutput device failureNOTE: The stacker or stapler/stacker LEDis continuously illuminated in

Check to make sure all settings are set as they should.  Sometimes when you try printing out a configuration page the printer will not print the IP configuration page.  This can

Contact an HP-authorized service or support provider. 20 INSUFFICIENT MEMORY For help press Product illustration alternates with 20 INSUFFICIENT MEMORY To continue press Product illustration The printer received more data than They were torqued in real good. The document, Interpreting control-panel messages , lists the most common messages that require attention or that might raise questions. HP LASERJET 4350 ERROR 66.00.15 EXTERNAL DEVICE FAILURE The stacker or stapler/stacker was removed and then replaced with the printer power was on.

HP 4350 ERROR 68.X PERMANENT STORAGE WRITE FAIL A nonvolatile storage device is failing to write. WAITING FOR TRAY XX TO LIFT alternates with The specified tray is in the process of lifting the paper to the top of the tray for proper feeding. and may not be used without advance written permission of PrinterTechs.com, Inc. http://upintheaether.com/hp-laserjet/hp-4350-driver-error.php Laser Jet 4350 error 13.02.00 Jam exists in the top cover area, HP 4350 13.02 error indicates that the media did not pass the sensor (ps103) in time.

Laser Printer Services provides HP LaserJet 4350 printer repair and LaserJet 4350n printer maintenance service in Los Angeles, Orange County, Riverside and San Bernardino. Release and scroll down to cold reset and press the check mark button. It can not be the laser/scanner since that will cause void areas of toner, but not cause extra toner on the paper. See Print-cartridge motor (HP LaserJet 4250/4300/4350 series printer only). 4 Replace the dc controller PCA.

What am I missing? For the 4000, 4050, and 4100 series the paper feed assembly could be bad. Does anyone know what the fix is.... by Greyhead98 on Nov 8, 2011 at 11:48pm Add comment Please sign in to comment 0 Hi , Need help.I have a hp 4350 laser jet printer with fuser related print

HP LaserJet 4 plus printer repair | HP 4M plus, 4/4M service HP LaserJet 5/5M/5N printer repair | HP 5/5M/5N printer service HP LaserJet 5P/5MP, 6P/6MP printer repair | HP 5P/5MP, Then reboot printer AND computer, reconnect cables, and try printing again.  6. is an HP Authorized LaserJet repair center in Los Angeles, Orange County and Ventura.  Our team of experts will help resolve your LaserJet printer  issues quickly and efficiently. Table 7-7 Numerical printer messages (continued) Display-message troubleshooting 363 Control panel message Description Recommended action To continue turn off then on 3 Reseat the formatter. 4 Go to http://www.hp.com/go/lj4200_software, http://www.hp.com/go/lj4250_software, http://www.hp.com/go/lj4300_software,

A short delay should occur between when the tray closes and the tray-size message appears on the control-panel display. CORRUPT FIRMWARE IN EXTERNAL ACCESSORY For help press The printer detected corrupt firmware in an input or output accessory. Printing can continue, but the printer might behave unexpectedly in response to the changed settings.