Home > Hp Laserjet > Hp Laserjet 4200 Error 13.06

Hp Laserjet 4200 Error 13.06

When handling DIMMs, either wear an anti-static wrist strap or frequently touch the surface of the DIMM anti-static package, then touch bare metal on the printer. There is no other thing that can cause that specific problem as the Manual feed uses the same paper path except for the small portion that comes up from the paper In addition, the printer displays warning messages, error messages, and critical error messages. Look for the jam in another location and/or contact HP, or an authorized service provider. this contact form

If the paper is stuck in a tray, try removing it through the tray above (if applicable) or through the top-cover area. You did not respond to my post and it would help to know if it still jams when coming out the back faceup rather than facedown. Do not attempt to grasp the paper as it exits the duplexer to the output bin. Figure 58: Loading paper Make sure that the stack is flat at all four corners and that the top of the stack is below the maximum-height indicators.

X Description 3- EP cartridge fan, right side (HP LaserJet 4300 only) 4- Main cooling fan, left side Action Turn the printer power off and then turn the printer power on. Remove all paper from the output bin. Figure 17: Rotating the paper guide Replace the entrance cover and close Tray 1.

X Description 1- Unknown misprint error 2- Beam-detect misprint error 4- No VSYNC error 7- Feed delay error 9- Signal noise error Action Press the (Select) button to continue or press The laserjet 4200 printer is unable to read the electronic information (e-label) on the print cartridge so that the printer can keep track of the page count for the print cartridge. The toner cartridge was installed with the sealing tape installed. 55.X PRINTER ERROR. Figure 51: Closing DIMM access door Set the bottom of the cover onto the printer.

Remove all non-HP paper-handling devices. HP LaserJet 4200 service error codes we repair in Southern California! 10.XX.YY 10:00:00 Supply memory error. My 4th visit and now DC controller is Next ?... http://www.fixyourownprinter.com/posts/75177 A page shorter than 200 mm was sent to the duplexer.

Some non-HP parallel cables might be missing pin connections or might otherwise not conform to the IEEE-1284 specification. Action Turn the printer power off and then turn the printer power on. Figure 37: Removing the rear output bin Firmly grasp each side of the fuser. Figure 12: Clear the message If the above action does not solve the issue, contact HP, an authorized service provider, or look for the jam in another location.

Figure 16: Opening Tray 1 and removing entrance cover Rotate the paper guide to check for additional jammed paper underneath.

If not then it has to be the back cover or the facedown exit parts. The fuser fuses properly as well. Turn the printer off and then turn the printer power on.

Figure 25: Inserting staple cartridge The stapler needs to reload after clearing a staple jam, so the first few documents (up to five) might not be stapled. weblink If the above action does not solve the issue, contact HP or authorized service provider. by moe on May 10, 2013 at 11:28am Add comment Please sign in to comment Thanks, I thought the sticking was caused by magnet "leaking" into the area underneath the sponge, The media is probably wrapped around the fuser roller. 13.98.00 open input trays then open and close top cover The rear output bin was opened when the printer was attempting to

Figure 40: Inserting fuser Install the rear output bin. CAUTION: Ensure that all jammed paper is removed before closing the cover or tray. If the above action does not solve the issue, contact HP or an authorized service provider. navigate here You can change this preference below.

i have changed the delivery assembly, fusing unit, all feed/pick up rollers .had a new cartridge but still jams HELP ! There is a plastic latch at the right side near the top and two on the left with triangle symbols pointing at them. Plug the printer into a wall outlet and see if this resolves the problem.

CAUTION: Do not fan the paper.

Amazon, the Amazon logo, Endless, and the Endless logo are trademarks of Amazon.com, Inc. by moe on May 10, 2013 at 11:59am Add comment Please sign in to comment 0 Thanks Moe,Regardless of made in china or not, if this cannot be fixed, we will LaserJet 4200 51.2 Laser Error 52.XY printer error 52.0, 52.1printer errors A temporary printer error has occurred. 52.0- Scanner error 52.1- Scanner startup error 52.2- Scanner rotation error 1. by wlulham on Oct 4, 2006 at 1:38pm Add comment Please sign in to comment 0 There is a service note covering swing plate replacement on 4250/4350 printers.Only a certain serial

Figure 32: Inserting the duplexer Open and close the top cover to clear the jam message. If the error persists, replace the stapler cartridge. A nonvolatile storage device is full. his comment is here After clearing all jams, send the print job again because the printer power has been turned off.

Action Press the (Select) button to continue. Push the blue levers upward and pull the fuser straight out of the printer. When it jammed if one opened  the door and removed the toner cartridge, there was   1 or two pieces of paper wrinkled up right in front of the fuser  with Figure 54: Removing the tray Pinch the release that is located on the left guide and slide the side guides to the correct paper size.

Critical error messages Critical error messages display warnings about device failures. If the above action does not solve the issue, contact HP or an authorized service provider. 13.XX.YY JAM IN TOP COVER AREA Description Paper has jammed in the top-cover area of Right side cover removal: Pull the drawer out. If the error persists contact HP or an authorized service provider.

Disconnect all optional paper handling accessories and try printing again. Pressing the Select (check) button should clear the message. top 41.X PRINTER ERROR For help press ? Open and close the top cover to clear the message.

Open the top cover and remove the print cartridge. Action Press the (Select) button to continue. Action Check for a loose cable connection and make sure to use a high-quality cable. Remove all paper that is found within the paper path, and then reinstall the cartridge.

The right cover is held in by latches. HP LaserJet 4200 13.06.00 error means that a page is jammed near the output door. If CLEARABLE WARNINGS is set to JOB in the printer configuration menu, these messages are cleared by the next print job. (Click here to see the description of CLEARABLE WARNINGS under top 79.XXXX PRINTER ERROR To continue turn off then on Description The printer detected a critical hardware error.

Scrape off the sticky residue and replace it with some thin sticky back felt.