Home > Hp Laserjet > Hp Laserjet 4100tn Error

Hp Laserjet 4100tn Error

Contents

by unknown on Feb 9, 2011 at 5:49pm Add comment Please sign in to comment 0 jnichols22: seeing that it goes back in a bit, yes by unknown on Feb 23, IIISi/4Si Only: 1. Reseat connector J201 on Sensor PCA. 3. IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si his comment is here

Reinstall and watch again from the back. Bad cassette microswitch. 2. My 4100 had developed the dreaded paper jam described above and I had no idea what was causing it. You need something there to keep the plate from sticking whether from residual magnetism or left over goo. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=83436

Hp Laserjet 4100 Not Printing

Replace DC Controller PCA. 57.2 ERROR 1. Printing a single page from Tray 2 worked fine. by dmzcompute on Nov 9, 2009 at 4:30pm Add comment Please sign in to comment 0 i just replaced the engine control board and still the same thing ..

II, IID Only: 1. 53 Error - Replace memory card. What else could be causing this problem. Get 1:1 Help Now Advertise Here Enjoyed your answer? Cleaned and lubed all shafts gears and rollers.

I have replaced the rollers; however, this has not fixed the issue. Hp Laserjet 4100 Manual Fold down the rear output bin at the back of the printer, and remove 2 screws (see picture, screws circled as #1) hidden underneath the lip of the top rear of I did find the one behind the manaul paper tray and cleaned that but where is the one for tray 2 ? For LJ III, IIID, IIIP, IIISi/4Si with 1 MB extra memory, enable page protect. 22 ERROR/ I/O CONFIG ERROR 1.

IID, IIID Only: 1. Reassembled, and I got error 13.1 after it seemed to just spin (no paper movement/output). It will be tight, but you still should be able to move it. Paper Control PCA malfunction. 3.

Hp Laserjet 4100 Manual

Inspect toner level sensor connector for damage. 4. https://www.experts-exchange.com/questions/21900490/Hp-Laser-Jet-4100N-has-an-error-of-EIO-2-ERROR-82-0180-and-will-not-print-PLEASE-HELP.html Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers Hp Laserjet 4100 Not Printing Look at your computers first. Hp Laserjet 4100 Driver Install new toner cartridge. 2.

Replace MIO card. 3. http://upintheaether.com/hp-laserjet/hp-laserjet-error-52.php Printing multi-page documents from tray 2 would always cause an extra page to be printed which would jam (Error 13.6 mostly for me). Easy to check. Reset inteface cable 3.

Defective fan, PS4 or PS5 4. a. Disconnect the toner cartridge drive arm by using needle-nose pliers to squeeze the pin and push it back through its retaining hole on the top cover.  See picture below. weblink It is held in place by 1 screw.

There is a selenoid with a "L" shaped arm which sits in a opening in the gear assembly and prevents it from moving. by startrek133 on Nov 9, 2009 at 7:06am Add comment Please sign in to comment 0 ok just replaced the tray 2 pickup assembly and still get the same problem .. Replace DC Controller. 52 ERROR Cycle Power A scanner subsystem problem exists. 5Si/4000/4050/4100/5000/8000/8100 Only: 52.1 Scanner start-up failure. 52.2 Scanner rotation failure. 53 ERROR (Accessory Memory Error) 2686 Only: 1. 53

The foam in the solenoid was flaten and there was a delay in the release due to that being sticky.

Temporary printer error, check printer's configuration. 57 ERROR II, IIID Only: 1. 57-1 Error - Incompatible memory card in front slot. 2. 57-2 Error - Incompatible memory card in rear slot. Turn the printer off, remove the EIO accessory from slot 2, install it in a different EIO slot, and turn the printer on. 4. Duplex mechanism has failed 70-71 ERROR 1. Defective Interlock Switch Assembly. 4/4M/4+/4M+ Only: 1.

IIISi/4Si Only: 1. This issue will reoccure unless I print the first 3 sheets through tray 1. There is a spring on the left side of the pick up roller shaft that pulls the pick up shaft to make sure the half-moon rollers are facing up when the http://upintheaether.com/hp-laserjet/hp-laserjet-error-64.php If that is the case the only thing that can cause the issue is the sensor flag That activates the sensor on the ECU located behind the paper feed assembly.

Clearing the jam and closing the cover resets the printer until you print 3+ pages again and the cycle repeats. Do I need to remove filings from the clutch? Join Now For immediate help use Live now! DC Power Supply/Main motor driver malfunction.

There is a small spring that holds the L-arm to the solenoid. The longer it runs, the hotter it gets and the more prone to sticking it gets. Remove optional I/O PCA, then re-test. 69.x SERVICE 4000/4050/4100/5000/8000/8100 1. When printing on Trays 2 and 3, the printer will feed a blank sheet and then throw a 13.1 Paper Jam error.

Replace Formatter PCA. 3. If that flag is broken and does not activate when paper starts up the path then the printer does not know paper has started to move and when it reaches the Check paper feed roller. There is no paper jam and simply opening and closing the top cover will clear the jam.

The problem also occurs if I remove tray 3 from the printer. An easy fix! - Продолжительность: 7:47 maximpulse 391 294 просмотра 7:47 HP Laserjet P2015 Error: paper jam & toner lights - Продолжительность: 2:44 GOR Tools 79 856 просмотров 2:44 Replacing fuser maintenance kit paper late jam. Once the control panel overlay is removed, use a flat-blade screwdriver as shown in picture below to release the retaining clip from each side of the control panel, then rotate the

Check tansfer roller. Just follow the wires that run into the square box with gears on the right side of the plate. The printer would print two or three pages normally, followed by a single blank page, and then the motor would keep spinning with no paper coming through.This forum is terrific! Replace both at same time.

Hopefully this little synopsis will help.