Home > Hp Laserjet > Hp Laserjet 4100 Error

Hp Laserjet 4100 Error


Paper tray empty or not seated correctly. 2. Trying to print envelope in duplex mode (envelopes cannot be duplexed). I read the troubleshoot and knows that code means the Memory in the third DIMM slot has failed the RAM test.I changed the memory and also replaced the Formatter board. External fuser access door not closed. 4P/5P Only: 1. navigate here

IIISi/4Si Only: 1. by dmzcompute on Nov 10, 2009 at 8:29pm Add comment Please sign in to comment 0 yes i have replaced the tray 2 pickup assembly , and yes it works fine This error can be caused by Paper Feed problems. 41.1 or 2 Error or 41.3 Error All Printers There is a paper multifeed or the wrong size of paper is being Thank you in advance for your assistance. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=83436

Hp Laserjet 4100 Error Codes

Privacy Policy Terms of Use PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support The last thing to do would be replace the pick up assembly Tray 2, 250 sheet (part# RG5-2672); Tray 3, 250 sheet (part# RG5-2684); Tray 3, 500 sheet (part# RG5-2672); Tray DC Power Supply/Main motor driver malfunction. Cycle power. 4.

Just set the top part (engine module) to the side in a safe place. Covered by US Patent. Replace toner cartridge. 2. Hp Laserjet 4100 Driver III, IIID Only: 1. 53-1 Error in front memory slot. - Replace memory card. 2. 53-2 Error in rear memory slot. - Replace memory card.

If the clutch does not separate you have the new type and it will not be the issue. It might be necessary to use a small flat-blade screwdriver to release the tab inside that small hole.  Hold the output assembly in place (located at the top toward the rear Reset inteface cable 3. will check the sensor flag and see what i find , thank you !!

a. First - for an overview, you are trying to open the printer to get to the "Tray 2 Pickup Solenoid" (labeled: SL101 on page 266 of the service manual) To get Replace Interface/Formatter PCA. Defective display cable, display, or Formatter PCA. 11 PAPER OUT 1.

Hp Laserjet 4100 Not Printing

Does anyone have any idea of what could be the issue with this printer. https://www.marketpoint.com/13-1-paper-jam-error-hp-laserje-4000-4050-4100.aspx Replace DC Controller PCA. 57.2 ERROR 1. Hp Laserjet 4100 Error Codes Just follow the wires that run into the square box with gears on the right side of the plate. Hp Laserjet 4100 Paper Jam Please wait while we process your request.

Replace Formatter PCA. 69 SERVICE 1. check over here Replace DC Controller PCA. 2. by unknown on Dec 17, 2011 at 7:50am Add comment Please sign in to comment 0 Followed the instructions, replaced the solenoid strike plate, still received the error. If the paper seems fine then turn the machine around and remove the dust cover if it has one. Hp Laserjet 4100 Manual

Cycle power on the printer. 2. Used electrical tape to keep the flapper from clicking when it closes.She is printing perfectly and with all these new parts ought to be good for about 1 million more pages! Check Fan 3, replace if necessary. 4000/4050/4100/5000 only: 57.4 Printer Fan 57.7 Duplex Fan 8000/8100 only: 57.2 Fan 3 location: formatter 57.3 Fan 2 location: Low-voltage powersupply 57.5 Fan 1 location: his comment is here IIISi/4Si Only: 1.

by startrek133 on Nov 11, 2009 at 11:10am Add comment Please sign in to comment 0 Try replacing the sensor that sits in the ecu cavity and is connected via yellow Here's what my book says.53.xy.zzx=RAMy=internal memoryzz=Failed RAM test by moe on Feb 27, 2007 at 5:06pm Add comment Please sign in to comment 0 Moe is 100\% correct. Duplex mechanism has failed 70-71 ERROR 1.

Pro Slate 12) OR Browse all HP products Please wait while we process your request.

by luterocoruna on Jan 20, 2015 at 6:30am Add comment Please sign in to comment 0 I am pretty late to the party for this discussion but I am incredibly thankful Replace Formatter PCA. 4. I replaced a number of rollers only to have the same problem re-occur with no solution in sight.I recently found this web posting and tried the method described above in an Replace Laser Diode Assembly. 3.

Remove RAM expansion card. Press CONTINUE. 2. by dmzcompute on Feb 14, 2010 at 5:20pm Add comment Please sign in to comment 0 Is this a related issue, i.e. http://upintheaether.com/hp-laserjet/hp-4100-error.php Cleaned and lubed all shafts gears and rollers.

Sensor arm stuck or broken. 12 PRINTER OPEN 1. Computer power is off. 23 I/O NOT READY 1. Computer is powered off. 3. Replace Cable, DC Controller to H.V.

If the fuser does not turn on check SW101. 3. We disassembled the entire tray 2 assemblyand completely cleaned the solenoid and it worked! Easy to fix, but hard to get to. Top cover open. 2.

Check that PS1 is blocked by the latch flag. Replace Main Motor PCA or Main Motor. 4. At least one of two tabs must be present. All the pick ups are looking good.

Reseat connector J201 on Sensor PCA. 3. One feed roller is in the cassette tray and the other is right above it in the printer cavity. Sending a blank sheet tells me it is picking up the paper, but not printing it. Felt also dampens the noise the sponge crap was there for.

View more error codes What our customers are saying He made no charge for this service.” “ Kenneth Spencer KA Spencer Software Other companies couldn't repair my printer and could only Here you just need to remove the 4 screws that hold the tray 2 paper-feed plate. when i replaced the tray two pickup assembly , i took the whole thing around and broken it into two peices the part the bottom and top and replaced the whole There is no real paper jam that I can see.

Memory passed the ram test but the printer is still not working.