Home > Hp Laserjet > Hp Laserjet 4100 Error Codes

Hp Laserjet 4100 Error Codes

Contents

Replace Paper Input PCA. 5. FONT COLOR="orange" size=4>4000/4050/4100/5000/8000/8100: 1. Replace MIO card. 3. If so turn the power off and remove the screws which secure the formatter and slide the formatter out. this contact form

You can try reducing the DPI or unticking the collate option in the printer driver. It is dated 20010524. I used the download manager to update the firmware on one of our HP 4100Ns and I am going to watch and see if that fixes it (I've gotten burned in II, III Only: If no jam visible: 1.

Hp Laserjet 4100 Not Printing

Inspect pins on formatter MIO connection. 2. I have removed and reseated the HP DIMMs and restarted the printer with no success.I would appreciated any suggestions. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device. All of them are fine except for the HP LaserJet 4100Ns.

Now turn on the printer and see if you still get the error. Inspect the Fiber Optics Cable for cuts or kinks. 2. I quickly removed the power and after the socket was wired properly I plugged it back in to get this error. I have seen it with horizontal lines on the drum caused by the ecu and we had to change both the ecu and the toner cartridge.

Simplify print job. 2. IIISi/4Si Only: 1. a. Reseated the fuser assembly, since I couldn't think of anything else.

The look very deliberate, not like artifacts. Note IIP, IIP+, IIIP: Short C212 on the DC Controller to bypass error 50 time delay. (The printer must be turned off.) IIISi/4Si Only: 1. Replace PS1 if defective. 2. IIP Only: 1.

Hp Laserjet 4100 Manual

IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si Replace Scanner Assembly. Hp Laserjet 4100 Not Printing Replace Duplex unit. 54.1 Remove sealing tape - 4100 only: Toner cartridge has been installed without removing sealing tape 54.4 error - 4100 only: Problem exists with customers line voltage 55 Hp Laserjet 4100 Driver Privacy Policy Terms of Use Sign Up Login Add Question unknown asked Nov 5, 2002 at 7:10pm 1 HP LaserJet 4100 HP Laserjet 4100 In the error code 49-4C03 erroc code

Laser Malfunction See Error 51. 53.XY.ZZ Memory Error Cycle Power. http://upintheaether.com/hp-laserjet/hp-4100-service-error-codes.php The charge is stopped and the flapper is supposed to return back and stop the rollers. Paper pickup clutch turning more than once? by Brian on Jan 17, 2005 at 11:48pm Add comment Please sign in to comment WHY ARE THERE ALWAYS THOSE WHO WANT TO CORRECT SOMEONE'S TYPING INSTEAD OF ANSWERING THE QUESTION?Just

This is the electronic information, or e-label, on the print cartridge. The same error remains after removing the known-good extra memory.Did I damage a good formatter board in the the process of snapping in the new memory, and perhaps pressing too hard?Would Use a qtip shaft to activate the button. navigate here As to the firmware, call hp customer care and tella them you are having a problem with 49 errors and someone told you there is a service note on the firmware

Not sure if it is the engine, the engine board, or anything other problem. Personality cartridge installed in font slot is incompatible with printer. 72 SERVICE 1. Remove Dimms, cycle power 4.

Click here to purchase the laser scanner assembly.

I can't find it listed anywhere. If after moving the chips, the display is still not on, the formatter they sent you is bad. Replace Laser/Scanner Assembly. 3. Remove all EIO devices from the printer. 8.

And some times with a 49.ff.81 service error...anyone can help me what it is..please?Thanks guys by unknown on May 13, 2006 at 11:51am Add comment Please sign in to comment 0 Those aren't that hard to swap. Replace font cartridge. 2. http://upintheaether.com/hp-laserjet/hp-4100-error-codes.php Once you turn them off and on again they are fine.

It's datecode is 20010524 01.016.0. Replace Formatter PCA. 64 error 4000/4050/4100/5000/8000/8100 only: A scan buffer occurred - if it persists replace formatter. 66.xx.yy error 4000/4050/4100/5000 only: An error occurred in an external paper handling device, stapler/stacker. If you need instructions click on the link by my name and email me and I will use yousendit.com to send you the service manual which gives complete instructions on how Now the paper keeps jaming, which also seems to be jam just at the start of the fuser.

Computer is powered off. 3. Disassemble clutch and re-grease. Replace High-Voltage Power Supply. 20 ERROR/MEM OVERFLOW/INSUFFICIENT MEMORY 1. You can also take the formatter from the 4100 and put it in one of the 4050 and see it it works.

I just want to make sure I get the right board, and it seems like the same part has been called a DC controlller, engine control board, and controller board. There is a service note from HP. by risof on Apr 15, 2005 at 1:03am Add comment Please sign in to comment 0 Risof,The hard disk has gone bad or the EIO slot which it fits into. Press CANCEL JOB to clear the print job from the printer memory. 2.

Working on so many printers and some having different designations sometimes causes confusion. by dstal on Mar 12, 2006 at 9:30pm Add comment Please sign in to comment Do you really have 256mg (milligrams) of memory?256Mb (megabytes).Try starting the printer, firstly with the network Paper Control PCA malfunction. 3. See error 51.