Hp Laserjet 4000n Error Codes
http://www.fixyourownprinter.com/kits/hp/K41The solenoids have to have a pad to dampen the noise and prevent residual magnetism from holding the plates down. Release the checkmark (Select) button. 6. Make certain the paper is stacked approximately under the paper manual for guarantee that over filling is not the issue. Who would believe the grey roller at the front of the trey would cause such a problem, but simply pushing it back in made it start printing. this contact form
Replace the fan. Why this goes some way to solve 41 problems, I don't know. Do not attempt to do this from the top to bottom as you could break the feed sensor flag. HP LaserJet Pro MFP M125a Driver Download HP LaserJet Pro MFP M125a Driver Download HP LaserJet Pro MFP M125a Driver Download - The HP LaserJet Pro MFP M125a is a mono http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=25474
To review the food rollers, perform the accompanying directions: Turn the printer off. Utilize the occasion log to diagnose and troubleshoot irregular disappointments. eCommerce Solution : k-eCommerce My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance? The clutch issue usually will produce a 13 paper jam error not the 41.5 misfeed error.
by Smithjohn on Jul 5, 2012 at 7:35am Add comment Please sign in to comment 0 I know this thread has been going on for a very long time but....I only So be skeptical of sticky solenoids, etc, it is usually the rollers, or the clutch if it binds up and doesn't provide some slippage. (See the service manual if you don't Lighter fluid is the best cleaner for the solenoid to remove the gooey adhesive on the flap and solenoid body. It's possible that the sensor wasn't fully seated or got jostled during shipping so it sits at an angle and the sensor flag will periodically catch on it.
and may not be used without advance written permission of PrinterTechs.com, Inc. The printer passes the paper path tests for all paper trays. Cleaning or replacement of the refeed assy has cured it everytime.http://www.partsnow.com/service_today/1102.asp is a very informative and technical helper on this issue. http://www.metrofuser.com/error-codes Thanks again!! - Anonymous 0 If you read my original post, I indicated that most of the time this error occurs when the separation roller comes off the shaft.
System error 05:10 (DJ 800 only) Formatter card failure, or Formatter card not detected System error 05:10 (DJ 500 only) HP-GL/2 accessory card failure System error 06:03 (DJ 800 only) Hard Examine the paper way and all paper way mechanical get-togethers in the area where the issue can be disengaged. I've open up the printer to see if theres any breakage of the sensors actuators or any been knock out of positions but theres none. When I reset it to single-side printing everything was fine again.
Press and hold down the checkmark (Select) button while the memory is counting. http://www.printertechs.com/maintenancekit-instructions/hp-laserjet-4000/109-hp-laserjet-4000-reset-maintenance-count If the paper is not stuck on the sensor flag, it might start up and appear to be running OK until you print and the paper gets jammed in the front Turn the printer off. 2. Simultaneously hold down the minus side of the Item key, and the minus side of the Value key. 3. Turn the printer on while holding these My guess is that it will.
We tear apart, rebuild, and test HP LaserJets and LaserJet assemblies all day. weblink To perform a paper way test, allude to the accompanying directions: Press MENU until INFORMATION MENU shows up in the printer show. Had the same error. Discharge the lock and lift the spread inside the tray.
I opened the paper tray as you suggested and saw the roller had slid to the left. We are best at HP LaserJet service error code repairs in Southern California! If you wont be able to return or want to do a replacement to be sure, look up the paper feeder assy (sometimes known as refeeder) for the 4000 and get http://upintheaether.com/hp-laserjet/hp-laserjet-4m-plus-error-codes.php When that happens the first page is a blank page, the error 41.5 appears and then the next pages appear with no problem.
You may have to remove tray 1 as well, I forget as I have Designjet things running through my head presently and haven't torn down a 4000 or 4100 in a Verify the environmental thermistor cable is securely connected. 3. If there is no glue, why would it stick?Thanks again - it is nice to see a familiar name (you helped me get fusers to repair printers in the past). -
I only get intermittent 41.5 errors.
That may be you case and then again it may not. Problem solved in about five seconds. I've rescued many a clutch with it, fixed a few scanner motors, and even a few recalcitrant locks. HP DeskJet 1112 Printer Driver Download HP DeskJet 1112 Printer Driver Download HP DeskJet 1112 Printer Reviews - Printer in an instant.
Check sensors Ps102 and Ps103 to check whether they signal the right blunder messages and come back to READY. NOTE: Do not fan paper. Clearing the Maintenance Count and Service Message on HP LaserJets 8000/8100 series How to Reset maintenance count on HP LaserJet 8000, 8100 & 8150 The Service Manual indicates you need go http://upintheaether.com/hp-laserjet/hp-laserjet-4250-error-codes.php Remove the top, sides and tray 1 assy to get to it.
HP Laser-jet 4000 51.1 is Beam detect error and 51.2 is Laser error 52. Turned out my duplexing option was enabled in the printer driver properties. The paper size scores ought to be adjusted. I suspected a tray issue, and changed the trays.
This is due to the many different formatter board revisions. HP Design Jet 1050c plotter repair | HP 1050c plotter service HP Design-Jet 1050c plotter repair | HP 1050c plus plotter service HP DesignJet 1055cm plotter repair | HP 1055cm Plotter