Home > Hp Laserjet > Hp Laserjet 4 Plus 22 Par Io Error

Hp Laserjet 4 Plus 22 Par Io Error

My PC is running win2000 and it does not recognize the printer if I turn it on after the PC is on. Posted to HP (Forum) by hardware on 05-29-2009 Problem: PostScript print jobs across WAN We scan 10-15 page PDF documents to our remote location. If I create a document that is 3 pages long it will only print page 1 and page 2 and the same ofcourse goes for any page rage past 2 pages. Slightly flex the housing and lift straight up and out of the printer. this contact form

Simply replacing the Triac is not recommended, there are two resistors, R102 & R103, and a solid state switch (SSR101) which should also be replaced. May be feed problem. If error persists you will need to replace the formatter PCA. And doggone it, People like me! http://www.fixyourownprinter.com/posts/22548

ERROR 51 - Service Improperly seated toner cartridge - remove and reinstall Laser shutter blocked or damaged Damaged fiber optic cable Defective Laser PCA - replace I/IID/III/IIID Defective toner cartridge - You can depress these by hand and hear them click. You should hear a definite clicking.

Back back to top How did we do? Any help would be appreciated, Thanks Neil ! 2. A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems. However, the number displayed will point you in the right direction.

Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again. HP Laserjet 4Si 22 ERROR 9. See information on secondary patterns below. http://www.verycomputer.com/14_34eeb70694e6cad4_1.htm You will have to remove the covers to do this.

FunkyWalkerPosted on Wednesday, March 06, 2002 - 10:05 pm: A good site that has diagrams of printers is www.printerworks.com/ webcam teens Posted on Friday, January 05, 2007 - 11:42 pm: Simplify the print job. Printing is OK, except... You may have to register before you can post: click the register link above to proceed.

Is the software set for the size you're using? http://www.mj-printers.com/discus/messages/22/1180.html?1168123238 Bad drive gears. Join over 733,556 other people just like you! Any idea what causes this > error?

For example, 1 = fan motor 1. weblink Press GO to resume printing. Reseat the cable and use only high quality IEEE 1284 compliant cables. 5Si Are you using a non-HP MIO device? Or the cartridge is bad.

Defective or incompatible memory card - remove card and power cycle the printer 3. Whether it's a number or a term displayed, printer errors inform the user of what is not functioning properly.There may be many reasons why, for example, you have a paper jam Press front panel button to wake up printer. http://upintheaether.com/hp-laserjet/hp-laserjet-error-64.php ERROR 80 80X.YYYY ALL Printers The EIO card in slot X has encountered a critical error -power cycle, reseat card then replace card if needed.

Add more memory. Check the feed and separation rollers in the printer and in the tray. Also check the toner level sensor and the toner cartridge itself for damage.

All rights reserved.

It still prints fine though. Of course it can happen at any page count. Add memory or simplify the print job. explicit C(): suggestion of meaningful (and easy) extension 7. 22 par 10 error? 8.

If the problem persists and is application specific, verify proper setup with application vendor. I will have purchasing call in an order. Check connections to DC controller - replace main motor 4L/4 Main motor problem, check gear train for binding. http://upintheaether.com/hp-laserjet/hp-laserjet-error-52.php Error 79 Software/drivers, Memory PCA's, Font-Macro-Personality Cartridges, option I/O Cards.

Toner Cartridge (4+ only) ERROR 80 ERROR 89 5L/6L Troubleshooting Information A common problem with this printer is feeding multiple sheets of paper. Also, current PCL will recognize older PCL's but not the other way. Press Select button to resume printing, some data loss will occur, you will need to add memory or reduce the complexity of the print job. HP printer 22 errors over PCNFS network. 12.

AnonymousPosted on Monday, March 19, 2001 - 8:37 am: 41.3 paper error appears now and again on my printer, could you tell me the solution please. HP Laserjet 4+ Error 22 and WIN 95 OSR2.1 2 post • Page:1 of 1 All times are UTC Board index Spam Report Hp laserjet 4 plus Log Out | Topics Also, ensure new IEEE1284 cables for the said printers as this error tends to reflect poor signal quality and win98 is a little more finicky... You can remove it and replace it with a piece of adhesive backed felt.

The halogen heater lamp may be burned out, it should have less than 5 ohms of resistance between the two pins of the connector on the right end of the fuser Reseat the card and if available, swap with a known working card. We got it this morning and I have it installed. The MIO card is defective or maybe just not seated correctly.

This is accomplished by removing the connector from it's mate and tweaking or bending in slightly on the connector tabs. If you don't hear the motor immediately and you don't have a paper jam, change the power supply. Note: A sticky solenoid can also be the cause of text appearing lower on each successive page. Remove and reinstall the supply, replace the supply.

This type of error can be caused by invalid print commands, corrupt data, or invalid operations. If serial the wrong pacing option is selected.