Home > Hp Laserjet > Hp Laserjet 4 Error Code 57 Service

Hp Laserjet 4 Error Code 57 Service

These can be set within the Remote Control Panel. controller board. Optional I/O card is not connected to an active LAN. 3. Works great and certainly solved the problem (as I expected it would). -Alan A. http://upintheaether.com/hp-laserjet/hp-laserjet-2430-service-code-error-23e12517.php

Defective Internal Memory - Replace Formatter PCA, check all cables first! Replace the controller board. Is the menu set for the size you're using? Add more memory. http://www.fixyourownprinter.com/posts/9213

is between 0000J00000 and 2949J2222 2. Replace the fan. Back back to top How did we do? I am new to this and do not want to screw this up.

Laser Malfunction See Error 51. 53.XY.ZZ Memory Error Cycle Power. If you want to attempt board level repair try the electrolytic capacitor, C702, 10 uF 50 VDC. If the message persists, reseat the fuser. Aloha from Hawaii contact hp chat support I have an HP Photosmart 7760 and this worked great for me!All Print Cartridges Are Being Rejected The power ...

Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Bad 47W resistor (1/4W) on the Fuser Safety PCA (connector J107 on the Fuser Safety PCA). (P/N FF1-3872-000.) 2. The fan 3 or the formatter fan has a error.2. http://h30434.www3.hp.com/t5/Inkjet-Printing/Main-motor-choice-to-solve-a-Laserjet-4-57-Service-error/td-p/4081954 The +5 VDC enables the +24A VDC.) "2.

Replace both at same time. Replace fan 43. Then put the printer back online and send a test job from the host computer via the parallel cable. General information with more detailed information available.

Bad drive gears. http://www.advancedlaser-hp-error-codes.com/error_57.htm Check the I/O connections and make sure the proper media is being used. HP LASER PRINTERS 2P, 2P+, 3P 1. Los Altos Hills, CA Thank you.

Top cover open. 2. http://upintheaether.com/hp-laserjet/hp-laserjet-service-error.php Back back to top How did we do? Make sure fuser is correctly seated to AC Power PCA. 2. Replace DC Controller. 52 ERROR Cycle Power A scanner subsystem problem exists. 5Si/4000/4050/4100/5000/8000/8100 Only: 52.1 Scanner start-up failure. 52.2 Scanner rotation failure. 53 ERROR (Accessory Memory Error) 2686 Only: 1. 53

Replace the D.C. is between 2925J00000 to 3047J999999. (2-diode to 3-diode upgrade corrects static caused problem.) IIP, IIP+, IIIP Only: 1. Values of X, Y, and ZZ are as follows: X = DIMM type 0 = ROM 1 = RAM Y = Device location 0 = internal memory (ROM or RAM) 1 navigate here Replace if either is bad. 4.

HP 4 error code 57 Does anyone know what error code 57 means in an HP laser jet 4 ?? 2. HP COLOR LASER PRINTER 8500, 8550 ERROR 57.1 1. Duplexer fan.

Replace DC controller.

Replace the low-voltage power supply.3. Remove EIO cards, perform cold reset 6. You might have to remove the main cooling fan to see this connection.5. Replace DC controller.   Home | Error Codes | Hp Printers | Toner Cartridges | Hp Printer Accessories | Hp Plotters Copyright © 2011 Advanced Laser Services, Inc.

HP4 Error 57 10. Short the pin closest to the front of the printer. (The printer must be turned off.) II, IID, III, IIID Only: 1. Replace the Fan motor ( FM2 ) power supply fan.2. his comment is here Reset Duplexer. 2.

Replace the bad fan.4. Verify that the SIMMS or memory cards are seated. Replace or clean as needed. Reseat DIMM, then Formatter - Replace or flash DIMM then formatter Back back to top How did we do?

Secure each cartridge by ... For example, 1 = fan motor 1. IIISi/4Si Only: 1. Also, can I get some instructions on putting in the rollers.

Check the printer’s configuration. 3. Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly. Articles Forum New Posts FAQ Calendar Community Groups Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Blogs Advanced Search Forum Printer Forums Hewlett Packard Laserjets II, III Only: 1.

Bad Fuser Safety PCA. (P/N RG1-0208-030.) Note 2686A/D: Short resistor R250 on the DC Controller to bypass error 50 time delay. Firmware updates are available for some machines at http://hp.com and clicking on the drivers and software tab. Replace toner cartridge. 2. Printing error occurred in one of the printer fans.2.

Defective D.C. Replace fan 23. Sign Up Login Add Question unknown asked Mar 26, 2003 at 12:47pm 0 HP LaserJet 4 HP 4 service error 57 I have purchased and installed the PCA motor kit to