Home > Hp Laserjet > Hp Laserjet 1100 Error In Printing

Hp Laserjet 1100 Error In Printing


do i need to change the motor part or it could be caused by something else? Share this conversation Related Computer Questions Question Date Submitted It says it is offline, but earlier today all was fine and it 10/17/2016 10/17/2016 Byron Lenovo g510 running win 10 stuck by unknown on Jul 10, 2005 at 6:00pm Add comment Please sign in to comment 0 Did you notice the reply directly above yours? Do you think it is the situation I should replace the cartridge? http://upintheaether.com/hp-laserjet/hp-1100-error-lights.php

I do not honestly know if this is a new problem or not.Just not having to fight the printer to a reset state and than to have it boot up normally it made no normal noise, but the two remarkable "ticks", the leds cycled on and off twice beginning from the most to the left, and on the end they are on If you open the toner door, on the frame near the top a little to the right of center is a switch which is activated by a plastic tab on the by dmzcompute on Aug 9, 2006 at 7:38pm Add comment Please sign in to comment I had the exact same problem - a printer here at work had the flashing yellow http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=25470

Hp 1100 Printer Driver

So I think may be there is some driver problem that scaner does not work. Copy button works perfectly but scan button dont work. now lets try and readd the printer.. ( i recommended the two exact devices above because they are recommended by hp support.. It seats at the most bottom inner of 1100 all of the covers has to be take off, then the left side's gear assembly and others , flip 1100 upside down

Checked to make sure cable connections are secure. on second thought, i think this printer has had it. I want to know how can I use its scaner?Kindly guide ...... Hp Printer You could smack it about a bit (the cartridge) to see if it loosens up but it may have to be replaced.Hope this helps?!Dazz UK by hpwizard on Nov 14, 2005

what happens? It sometimes pops out of its slot or the spring gets out of position and it does not return after paper passes over it and gives a constant jam error. There are two jam sensor flags one under the left paper feed roller support and one in the fuser exit area. http://h30434.www3.hp.com/t5/LaserJet-Printing/Windows-8-HP-Laserjet-1100-Printer-in-Error-Status/td-p/2349357 by nivek on Mar 4, 2009 at 3:48pm Add comment Please sign in to comment 0 Hi all.

Is there a quick solution to this problem?please Help by unknown on Jun 22, 2005 at 10:18am Add comment Please sign in to comment 0 i have the same problem with bahnee · 2 years ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Report Abuse Never really thought about that ashton · 1 month ago by moe on Aug 15, 2008 at 11:12pm Add comment Please sign in to comment did this still has spot. I've made a phonecall to a HP service and they've told me, that could be a heater or fuser error, and fixing the problem would cost almost that much I've bought

Hp Laserjet 1100 Printer

Faint printing corrected, but grey vertical smears on right and left margin plus grey areas in between. http://www.officemate.net/omkb/article.aspx?id=10738 Now when the USB cable is installed the system responds with 4 tones. Hp 1100 Printer Driver Would it also work if I used a USB adapter and plugged it into my cpu's USB port? Hp 1100 Printer Price Ask Dustin Your Own Question Dustin, Computer Support Specialist Category: Computer Satisfied Customers: 12502 Experience: I speak PC fluently, so you dont have to!

Mine blink faster than that. weblink When i try to print test page by pressing the button, it hangs trying to pick the paper.What could be the problem? Once it appeared it worked, on other times - no. If the self test works, the issue is the cable, driver or port on the computer or printer. Hp Laserjet 1100 Driver Windows 10

Summary:A jam occurs when the paper comes out of the top of the printer and just clears the paper exit sensor; a jam does not occur when the paper comes out When the transfer is done the blinking green light goes out. Thanks. navigate here The printer properties on the computer reports "out of paper" althought it isn't.

What happens if you push the button on the printer after it goes to ready. Approved: 5/3/2014 Easy fix to a frustrating problem! But the pc shows "error in printing" command.

Also, it still seems to like the second adapter, for whatever reason.Thanks for your efforts.

if so they should both give you the same pattern. A printer error message from my computer is saying the "printer is ot of paper" by unknown on Feb 19, 2008 at 11:40pm Add comment Please sign in to comment 0 Rated 9 out of 10 based on 6 votes. by dmzcompute on Feb 27, 2008 at 5:21am Add comment Please sign in to comment 0 my printer leaves a spot on the left side of each page every 3 inches.

You said you checked it, however, I have seen instances where the posts which hold the main board on the bottom break and the main board drops a bit and the Time for ebay! Connect the printer to a pc and send a two or three page job and tell us what happens. http://upintheaether.com/hp-laserjet/hp-laserjet-1012-error-printing.php if your not sure..

by moe on Jul 10, 2005 at 6:50pm Add comment Please sign in to comment 0 I, too, have an 1100 with a "fatal error." It also has a broken snap Printer won't let me print? What did you think of this article? You've got the service manual, good luck.

Any ideas? Plug in the printer and put in paper. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. This problem is only with the 1100ps because my 1055 prints like a champ.

by robis on Nov 12, 2005 at 2:41am Add comment Please sign in to comment 0 The winding down noise is the laser/scanner spinning to a stop.In the following anything in It was a really pitiful bandaid approach to fixing it and it's not the problem you are experiencing. Locate the two sets of rollers . This is like rolling back the odometer on a car.

It used to print just fine until just a couple of days ago. I'm not sure what else I can do. The visible rollers are clean, etc. That is why I sent additional XXX's and OOO's in my last entry to you, after I had already sent them to Stephen.

Make certain the Laser/Scanner Assembly is correctlyseated on the printer chassis.3. Between your advice and the advice you directed me to (DMZ), It is working. i did do what you asked however, and i press and pull on the bottom metal plate on the bottom of the printer and the whole metal piece does move. Article Attachments No Attachments Available.

second (smaller)green led blink when i try something to print. a litle one still flash, but nothing else happend. If it can see it, maybe it can now add it, and then store it in the software..i would remove the printer first through the windows 7 software, and then readd