Home > Hp Laserjet > Hp 6p Error Codes

Hp 6p Error Codes

Contents

At this point, it is the ONLY light on and stays on. Error 18 MIO Not Ready The printer is not connected to a LAN when it's expecting to see a LAN. X represents the error location and can equal one of the following: 1 = Slot number 1 2 = Slot number 2 3 = Slot number 3 6 = Card in LaserJet 5P/5MP Printers - Understanding the Front Panel Buttons and Status Lights 20. Check This Out

Faulty Connectors - Check J002 on DC controller and J601 on Laser PCA Low DC Voltage - Verify 12 VDC at J601-2 on Laser PCA Defective Scanner Assembly - Replace Laser Check PS701 and PS703 13.20/13.32 Paper stopped jam in paper path. On the right side of the fuser is a set screw - look in the area of the cover latch. Inspect the Fiber Optics Cable for cuts or kinks. 2.

Hp Laserjet 6p Driver

HP LaserJet 4 Plus/4m Plus Series Printers - Numerical Printer Error Messages/Parts Predict 11. Broken separation belt. 2. With (1), you must correct the issue and have that physical contact by cleaning the contacts or replacing the cartridge.

LaserJet 4100 Family Printers - Alphabetical Control Panel Error Messages 57. Replace main motor. Replace Cable, DC Controller to H.V. Hp Laserjet 6p Manual Replace DC Controller.

Duplex mechanism has failed 70-71 ERROR 1. Hp Laserjet 6p Printer Also check for any partially peeled labels, this can be a disaster if they come off inside the printer. LaserJet 3200 firmware update utility (English) 47. The steady amber error light returns.Is it something to do with the paper pickup assembly?

Call Toll Free (800) 551-1943 | OPEN M-F 8:30-4:00PM CST | Order Online Anytime! Hp Laserjet 6p Troubleshooting Reset Duplexer. 2. ERROR 43 / ERROR 43 OPT INTERFACE This indicates a communication problem between the formatter PCA and an optional interface installed (such as a network card). You could also have a defective or dirty exit sensor.

Hp Laserjet 6p Printer

This can generally get you 100 or so more pages. Bonuses Back back to top How did we do? Hp Laserjet 6p Driver On the III, IIID, IIIP, enable page protect if you have and additional 1 MB of memory installed. Hp Laserjet 6p Toner Colour LaserJet 4600 Series Printer - Control Panel Menu Definitions 73.

If worn, replace. his comment is here Back Error 11 - Paper Out Paper tray empty or not seated correctly. I have an HP Laserjet 6p that was on its way out to the dumpster when I rescued it. You have to remove the formatter to do the engine test. Hp Laserjet 6p Specs

Anyway, when I turn it on, the amber colored error light is the only light lit. LaserJet 8000 Series Printers - Using the Control Panel 79. Slightly flex the housing and lift straight up and out of the printer. this contact form LaserJet IIID printer - Control Panel Keys and Menu 06.

ERROR 40 - (Data Transfer Error) Momentary error, press "Continue" or "GO" to reset the printer 5L/6L Power Cycle the printer if error continues reseat the DC controller to Formatter 5P/6P Hp Laserjet 6mp Toner It is not cost effective to replace only the defective part - upper roller, single gear, etc. You should hear a definite clicking.

I am going to look the printer over better too.

If the lamp is discolored it's developed a leak at the glass to ceramic seal and the filament has oxidized and is burned out. Reseat the PostScript SIMM and/or replace it. Visually check or replace toner cartridge. 2. Hp Laserjet 6p Windows 10 Reseat connector J201 on Sensor PCA. 3.

That is why I put some extra effort into this, but apparently the light code can mean other stuff too. IIISi/4Si Only: 1. Like anything else, there are both acceptable and exceptional parts available. navigate here The halogen heater lamp may be burned out, it should have less than 5 ohms of resistance between the two pins of the connector on the right end of the fuser

Same results with the tray 2 installed.The rollers where the paper exit are also moving during this time as well.Nothing appears to be obviously broken or cracked with the upper or Improper MIO connection - look at pins on formatter MIO connection reseat card. The first location is just above the AC inlet either on the P/N label RG1-1782 or to the left of the label.