Home > Hp Laserjet > Hp 4si 79 Error

Hp 4si 79 Error

Contents

Paper Tray is overfull 2. X represents the error location and can equal one of the following: 1 = Slot number 1 2 = Slot number 2 3 = Slot number 3 6 = Card in Defective toner cartridge in the Laserjet 4 Plus only. Reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under the copyright laws.

Data LED is Blinking 6L,5L • The printer is set to manual feed. - Insert paper into the manual feed slot. HID, IID • The duplex paper path is obstructed or contains worn components. • The switchback assembly is misadjusted or bent. This error message usually pops up when a print job is corrupted. Back Error 12 Printer Open Paper path door (IIP/IIIP) or top cover open.

79 Service Error Hp Laserjet Pro 400

Reseat same No disk installed. ERROR 67 Defective formatter PCA On the 4Si this could be a temporary error which can be corrected by cycling the power 4V/4MV - This can also be a temporary error You can also try to upgrade the firmware as 79 errors are similar to 49 errors and can be firmware related. These are small rectangular blocks of plastic which contact the switches in the printer.

IIP, IIP+, IIIP Only: 1. 57 Error Unit 1 - Incompatible memory card in top slot. 2. 57 Error Unit 2 - Incompatible memory card in bottom slot. 57.x ERROR (IIISi/4Si On flash-memory-based products, you can update the firmware code by downloading the latest flash executable file for the product and running the program according to the readme instructions posted with the On the HP LaserJet/LaserJet Plus (2686A/D) this can be caused by a defective cassette micro switch in which case you will have to repair or replace it. Hp 79 Error Turn Off Then On This indicates a loose cable connection or a bad or poor-quality cable. - Reseat the cable and make sure you are using a high-quality cable (IEEE-1284). 36 - Control panel messages

Verify flag movement. 4=Fuser output, paper jam. 5, 6=Duplex module paper jam. HIP, IIP Plus, IIP • The scanner motor is bad. • The DC controller is bad. Note: A sticky solenoid can also be the cause of text appearing lower on each successive page. http://resources.lasertekservices.com/how-to-get-rid-of-service-error-79-on-the-hp-laserjet-pro-400/ Check duplex paper path for obstructions. 2.

If its damaged or worn, it won't open the laser shutter. 79 Service Error Hp Laserjet Pro 400 Mfp M425dn Error Codes - 41 50 Error/50 Service (fuser malfunction) All Printers • A temporary error has occurred. - Turn the printer off for 20 minutes to clear the temporary 50 Error. Replacing this should solve your problem. San Rafael, CA Great that you have that part in stock and thank you for your quick reply.

79 Service Error Hp Cp5225

DC Controller PCA malfunction. 4/4M/4+/4M+ Only: 1. http://webpages.charter.net/dperr/hp_error.htm ERROR 41-X X= 1,2,4,5 A temporary error occured - Press "CONTINUE" to clear. 41.3 Error - Unexpected paper size - more than one sheet of paper picked up. 79 Service Error Hp Laserjet Pro 400 Error 57 6L/5L Memory card incompatibility - 1,2,4,8 MB, 5 volt, 70 nanosecond or faster 6P/5P/5 Improper main motor function, check gear train for binding. 79 Service Error Hp Laserjet Pro 200 Replace Laser/Scanner Assembly. 3.

Recycle printer power. Verify that the C-link cables are installed correctly. Inspect Fiber-Optic Cable between Laser/Scanning Assembly and DC Controller. 3. The first thing to do is call hp since the unit should still be under warranty. Error 79 Hp Printer 1536dnf

Improperly seated SIMMs or font cartridge - remove, check and clean the contacts, re-install and try again. 2. If x=1 : Tray 2 lifter malfunction. Item Description Recommended Action 6 Error 53-0 ROM error See note below 7 Error 53-1 RAM error See note below Fatal Errors When the DATA, TRAY 2, TRAY 1 , and Restart printer.

It should not rub off! Hp Laserjet Pro 400 Firmware Update Use saved Parts Lists as templates to create new lists. If you do hear the motor reach speed and then you receive and error 51 you may have a defective laser diode although this is fairly rare.

Inspect the diverter drive assembly.

Can be defective or simply need to be reseated. IIISi/4Si Only: 1. Hence, I attempted to sort out the printer issue based on my years of experience. Hp Laserjet Pro 400 Error 49 Close Printer Cover/Printer Open All Printers The printer door is open.

Pretty rare though. IIISi/4Si Only: 1. Optional power stacker. Press continue or go on the printer to clear message.

Dirty or obstructed paper path. This is the board mounted to the DC power supply which is in the right front corner of the printer. Gently shake the toner cartridge both from side to side and from front to back. Press and release the front panel button.

You could also have a defective or dirty exit sensor. LJ8100/8150 A fan motor failure occurred. HP • For service notes between 2925J00000 and 3047J99999: - Replace the fusing assembly. Also on the 4V/4MV check the door open sensor (PS402) on the terminal board located under the transfer roller.

Replace PostScript ROMs. Order the HP IIP/IIIP 50 Service Error Repair Kit. Error Codes - 27 HID, III, iiD, II • The registration assembly is defective. • The fuser is defective.