Home > Hp Laserjet > Hp 4200 Printer Error

Hp 4200 Printer Error

Contents

The time now is 09:27 PM. What you say now makes sense. Check the configuration of the EIO (HP Jetdirect card) and the host computer. Turn the printer power off and then turn the printer power on. have a peek here

The best way to determine which fuser you have is to pull the fuser out of your printer and check the barcode label on the fuser. Disconnect all optional paper handling accessories and try printing again. Action Turn the printer power off and then turn the printer power on. If it slides back and forth check the motor mount. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422

Hp Laserjet 4200 Error Codes

Look for the jam in another location, contact HP, or contact an authorized service provider. Flex the arms on the plastic output bin slightly to remove one side of the tray at a time. Pressing the Select (check) button should clear the message.

NOTE: While duplexing the paper exits the top output bin momentarily and then travels back into the duplexer. Bitte versuche es später erneut. The media is probably wrapped around the fuser roller. Hp Laserjet 4250 Error 13.01.00 Jam In Tray 2 alternates with 68.X PERMENANT STORAGE ERROR To continue press (Select) Description One or more printer settings that were saved in the nonvolatile storage device are invalid and have been reset to

Life should NOT be a journey to the grave with the intention of arriving safely in an attractive and well-preserved body, but rather to skid in sideways - Coke in one Hp Laserjet 4250 Error Codes If that works then it could just be a tray problem those trays are cheap plastic garbage. These messages are not affected by the AUTO CONTINUE setting. http://h20566.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=412144&docId=emr_na-c00633921 Melde dich bei YouTube an, damit dein Feedback gezählt wird.

Almost sound like a timing issue or something related to the reentry of the paper if you had a duplex unit. Hp Laserjet 4250n 49.4c02 Service Error NOTE: Do not force the paper if it will not move easily. Please try the request again. If you are printing from Tray 1, verify that the correct paper size is selected at the printer control panel.

Hp Laserjet 4250 Error Codes

Loose toner should clear from the printer after a few pages are printed. check these guys out If the message persists, contact HP Customer Support. Hp Laserjet 4200 Error Codes Click here for instructions on how to print a Configuration page. Hp Laserjet 4200 Cartridge Installed Message Re-install the plastic rear output bin.

This error can occur if the driver being used is not IEEE-1284 compliant. navigate here The EIO accessory might be defective. If tape has been removed, replace the toner cartridge. by moe on May 11, 2005 at 3:40pm Add comment Please sign in to comment 0 There is an engine board in the 4200, it is mounted between the trays and Hp Laserjet 4200 And 4300 Series Printers Drivers

Next, lower the rear output bin cover as shown below. If jammed, paper is present, remove it. If the message appears only with a certain software program or print job, contact the software vendor for assistance. http://upintheaether.com/hp-laserjet/hp-4200-error-codes.php This is the small one with the two ribbon cables and various other connections hooked to it, mounted vertically.The Controller board you are talking about I don't see anywhere in the

Remove the spring, fold up one of the coils where the spring broke and reinstall.If the spring is attached, then either try a new tray (500 sheet tray part # RM1-1088] Hp Laserjet 4250 Error 13.20.00 Jam In Tray 2 NOTE: Avoid spilling loose toner. Wird verarbeitet...

by dmzcompute on May 12, 2005 at 3:38pm Add comment Please sign in to comment 0 I have worked on many many many HP 4200 series over the years.

If paper is difficult to remove, try clearing it from the tray area. The stacker or stapler/stacker LED is continuously illuminated in amber. There is a service manual for it in our reference section. 13.98 Paper Jam Press the Check button one more time to Print Menu Map and then press the Check button.

I guess I order a solenoid too? Attaches at the bottom and is so fun to reattach. Action Remove any jammed media from the paper path. this contact form Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions.

Turn the printer power off and then turn the printer power on. Thank you. replaced tray one input assembly5. If a duplexer is installed, remove it from the back of the printer.

If the above action does not solve the issue, contact HP or an authorized service provider. 13.XX.YY JAM IN TOP COVER AREA Description Paper has jammed in the top-cover area of Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. Action Turn the printer off and then on. If toner gets on your clothing, wipe it off with a dry cloth and wash clothing in cold water. (Hot water sets toner into fabric.) Figure 15: Removing the jammed paper

Figure 4: Opening Tray 1 and removing entrance cover Rotate the paper guide to check for additional jammed paper underneath. top 59.XY PRINTER ERROR For help press ?