Home > Hp Laserjet > Hp 4200 Error Messages

Hp 4200 Error Messages

Contents

Take a sharp tool, like a razor blade and scrape the buildup off these edges. HP Laser Jet toner cartridge part number Q1338A is to be used on HP LaserJet 4200 series printers. Locate the pre-feed sensor and look for a paper jam. CAUTION: Do not use a sharp object to clear paper from the fuser area. have a peek here

If replacing the Lifter Drive Assembly does not correct the issue, the DC Controller could be at fault. Make sure you have removed the plastic block (with #4 on it) and are pushing down on the #5. Turn the printer power off. Values of X and Y are as follows: X = DIMM type 0 = read-only memory (ROM) 1 = random-access memory (RAM) Y = device location 0 = internal memory (ROM Clicking Here

Hp Laserjet 4250 Error Codes

If the job prints, go back to the first program and try printing a different file. (If the message appears only with a certain program or print job, contact the software If the above action does not solve the issue, contact HP or authorized service provider. We got it this morning and I have it installed. IIISi/4Si check the door open sensor flag, PS1.

Configure is properly. X Description 2- air-temperature sensor 3- DC controller 4- power supply Action Turn the printer off and then on. Action NOTE: Press the ? (help) button for detailed information about clearing the jam. 13.98 Paper Jam This most likely means that there is a piece of paper wrapped around the fuse.

Upon start-up, HP printer will display ERROR 13.20.00 JAM TRAY 2. Hp Laserjet 4200 Cartridge Installed Message Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus! CAUTION: Static electricity can damage DIMMs. If you have an active support agreement or HP Care Pack, you can link them to your profile to ensure access to all services.

This can be checked by pulling out the tray and pushing in on the tray size-sensing switches; once depressed, you will hear the lifter motor begin running. Hp Laserjet 4250 Error 13.01.00 Jam In Tray 2 Turn the printer power off. If the problem persists and is application specific, verify proper setup with application vendor. If the above action does not solve the issue, contact HP or an authorized service provider.

Hp Laserjet 4200 Cartridge Installed Message

X Description 1- Unknown misprint error 2- Beam-detect misprint error 4- No VSYNC error 7- Feed delay error 9- Signal noise error Action Press the (Select) button to continue or press

Remove the print cartridge and check the paper path for paper. Hp Laserjet 4250 Error Codes Action Check for a loose cable connection and make sure to use a high-quality cable. Hp Laserjet 4200 And 4300 Series Printers Drivers Anmelden Transkript Statistik 236.802 Aufrufe 297 Dieses Video gefällt dir?

top top 40 EIO X BAD TRANSMISSION To continue press (Select) Description The connection has been broken abnormally between the printer and the EIO card (HP Jetdirect card) in the specified navigate here top 13.12.07 JAM IN STAPLER Description There is a jam in the stapler cartridge. Los Altos Hills, CA Thank you. Action Remove the printer from any UPS supplies, additional power supplies, or power strips. Hp Laserjet 4250n 49.4c02 Service Error

Don't replace: rejuvenate! Figure 26: Opening rear door Remove any paper found. How did we do? Check This Out Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers

You could also have a defective or dirty exit sensor. 13.20.00 Jam Inside Rear Door On the right side of the stapler/stacker, turn the stapler unit toward the front of the printer until the unit clicks into the open position. ERROR 59 Add Memory 4Si/IIISi Not enough memory for PostScript option.

If the error persists, contact HP support.

Pretty rare though. Nächstes Video How To Fix hp Laserjet 4200n 4300n 4250dn 4350dn Swingplate PART 2 - Dauer: 11:30 BrokenPrinter1 44.158 Aufrufe 11:30 HP 4200 4250 4300 4350 13.20 error on startup fix HP LaserJet 4200 service error codes we repair in Southern California! 10.XX.YY 10:00:00 Supply memory error. Hp Laserjet 4250 Error 13.20.00 Jam In Tray 2 If you don't know how to remove the fuser from your printer,it's not difficult -- see the removal instructions farther down the page.

Most times this can simply be reinstalled. Figure 13: Opening the top cover and removing the print cartridge Use the green handle to lift the paper-access plate. Figure 16: Opening Tray 1 and removing entrance cover Rotate the paper guide to check for additional jammed paper underneath. http://upintheaether.com/hp-laserjet/hp-4200-error-codes.php Pressing the Select (check) button should clear the message.

First page out is less than 9 seconds with a processor speed of 300MHz. Remove the duplexer if installed. top 13.13.00 JAM INSIDE DUPLEXER Description A page is jammed inside the duplexer. Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew

The ON setting determines that the clearable warning message appears until (Select) is pressed. NOTE: While duplexing the paper exits the top output bin momentarily and then travels back into the duplexer. Error 60.2 Tray 2 lifter motor error 62 NO SYSTEM. To much data sent to the I/O port - clear data with GO or Continue, data may be lost Is the computer on?!

Action Press the ? (Help) button for detailed information. Check connections to DC controller - replace main motor 4L/4 Main motor problem, check gear train for binding. top top 69.X PRINTER ERROR To continue turn off then on Description The optional duplexer is not functioning. Feedback?

Back back to top How did we do? Reinstall the stapler/stacker or stacker. No part of this site, or its source code, may be reproduced in any way. CAUTION: Ensure that all jammed paper is removed before closing the cover or tray.

The part number is RM1-0034-000. If this workaround is not acceptable or the error message persists after performing all of the recommended actions, contact an authorized HP Service or Support Provider: http://www.hp.com/go/support top 11.XX Internal Clock Pro Slate 12) OR Browse all HP products Please wait while we process your request. If the printer is already plugged into a wall outlet, try another power source in the building that is independent of the one currently being used.

ERROR 50.XXXX - ERROR 51 (Loss of beam detect) This is a beam detect error indicating a problem with the laser scanner. Is the paper size correct? All images and logos used with permission from the respective owners.