Home > Hp Laserjet > Hp 4100 Service Error

Hp 4100 Service Error


Inspect PostScript ROMs for bent or broken pins. 2. c. Defective display cable, display, or Formatter PCA. 11 PAPER OUT 1. You could call HP since they have had firmware errors and will send you a new firmware chip to install at no cost. have a peek here

But the ability to create custom scanning profiles a… Document Imaging Document Management OCR Images and Photos Photos / Graphics Software How to Request Attention Video by: Kline Need more eyes Please help & thanks in advance. It helped me immensely. At least one of two tabs must be present. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=83436

Hp Laserjet 4100 Error Codes

Any idea what I am doing wrong? Turn the printer on. 9. Hope this helps?!Dazz UK by hpwizard on Dec 26, 2005 at 6:30am Add comment Please sign in to comment 0 I have an HP Laserjet 4100n which does not appear to

Remove EIO cards, perform cold reset 6. We have different types of media in the trays and I want it to just indicate that it is out of paper and wait for more... Still no display. When first turned on, it runs memory check and then displays two lines of *****, after which the 55.00 error message comes on.

Also included in this estimate would there be a manual for how to perform this task? Hp Laserjet 4100 Not Printing Replace Laser Diode Assembly. 3. I don't hear the engine come on when it is turned on. https://fixyourownprinter.com/posts/28579 Thanks so much.

Make sure you do it with power off on both printers. The assembly has a metal flapper which is drawn to the center of the selenoid by a magnetic charge when the print cycle is started. Remove Dimms, cycle power 4. by dmzcompute on Nov 30, 2005 at 1:55pm Add comment Please sign in to comment Well, I ended up getting a refurbished engine controller board and after I replaced it, the

Hp Laserjet 4100 Not Printing

What is the error? original site At least one of two tabs must be present. 3. Hp Laserjet 4100 Error Codes by dmzcompute on May 4, 2006 at 1:59pm Add comment Please sign in to comment 0 The fuser may also be toast by dmzcompute on May 4, 2006 at 2:01pm Add Hp Laserjet 4100 Manual Remove optional I/O PCA, then re-test. 69.x SERVICE 4000/4050/4100/5000/8000/8100 1.

This has made no difference to the distance and it doesn't appear to be slipping.I am now thinking this is a sensor issue. navigate here Turn the printer off, and then turn the printer on. 3. IID, IIID Only: 1. I suspect that I am missing some critical part of the installation because only a single sheet, sans IP address information, is printing when I try and print the configuration information Hp Laserjet 4100 Driver

This is a very useful forum! You also may want to go to the information menu and run a menu map just in case there is some special setting which needs to be restored after the cold I used the download manager to update the firmware on one of our HP 4100Ns and I am going to watch and see if that fixes it (I've gotten burned in http://upintheaether.com/hp-laserjet/hp-4100-service-error-codes.php Check Fan 1, replace if necessary. 57.3 ERROR 1.

Replace font cartridge. 2. If the error persists, replace the firmware DIMM. 13. What Resolved Question: I have a 49.306D service error on a HP Laserjet 4100.

Replace Scanner Assembly.

Any suggestions? Working on so many printers and some having different designations sometimes causes confusion. At least one of two tabs must be present. 3. They are availble for about 200.00 on exchange.

The box in front of you is the formatter. Are their fuses? - Anonymous 0 Forget about fuses. Good Luck. http://upintheaether.com/hp-laserjet/hp-4100-error.php Your answer is 5 posts above yours, so you don't have to read the whole thing.

Add memory or simplify print job. 21 ERROR/PRINT OVERRUN/PAGE TOO COMPLEX 1. by Stephen on Oct 23, 2006 at 5:18pm Add comment Please sign in to comment 0 I am working on an HP Laserjet 4100TN... It is possible if the ecu was defective that it damaged the toner drum by engraving those lines into the drum. HP had a service note for bad firmware and you may want to call HP Customer Care to see if they still have it and if you can get a replacment

Corrupted print job, intermittent communication errors, etc..) For some reason, on the 4500 printers I saw, it always seemed to be the jetdirect card or a noisy ethernet cable. by Anonymous on Dec 8, 2005 at 6:48pm Add comment Please sign in to comment 0 I am working on a LJ 5si that has a blank control panel display. These resources can help you build awareness and prepare for defense. It has 256mg added third party memory.