Home > Hp Laserjet > Hp 4100 Printer Error Codes

Hp 4100 Printer Error Codes

Contents

Remove I/O cables. (Cable is hooked up incorrectly or bad interface in computer.) 2. As one can imagine there was great demand for the hp laserjet 4100 printer series when it was first introduced to the general public.  With such a strong demand, there was Visually check or replace toner cartridge. 2. Bad fuser bulb. 3. http://upintheaether.com/hp-laserjet/hp-4100-error-codes.php

Output selector knob is not in duplex position. If the paper moves forward and then comes back a bit, the problem is with the clutch in the tray. Replace Formatter PCA. 64 error 4000/4050/4100/5000/8000/8100 only: A scan buffer occurred - if it persists replace formatter. 66.xx.yy error 4000/4050/4100/5000 only: An error occurred in an external paper handling device, stapler/stacker. Power Supply (P/N RG1-0906- 000). this contact form

Hp Laserjet 4100 Not Printing

Wayne Haub Kansas City Help with HP printer problems and error codes. Remove and reseat the optional interface card. Watch the termination's on the network cabling. Broken separation belt. 2.

and may not be used without advance written permission of PrinterTechs.com, Inc. Back back to top How did we do? Formatter PCA malfunction. 3. Check RAM expansion card, reseat if necessary. 2.

Plunger missing on top cover. 2. Bad Fuser Safety PCA. (P/N RG1-0208-030.) Note 2686A/D: Short resistor R250 on the DC Controller to bypass error 50 time delay. Replace Formatter PCA. 69 SERVICE 1. http://fixyourownprinter.com/posts/45488 Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again.

Any help here would be appreciated too. Disconnect the toner cartridge drive arm by using needle-nose pliers to squeeze the pin and push it back through its retaining hole on the top cover.  See picture below. A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems. Add memory to printer or reduce complexity of print job On the 5P turn the image adapt and page protect to ON or AUTO.

Hp Laserjet 4100 Manual

I also tried a different fuser, so it can't be the fuser or fuser sensors, correct? LJ 4250/4300/4350 A printer fan is not funtioning. Hp Laserjet 4100 Not Printing Los Altos Hills, CA Thank you. Hp Laserjet 4100 Driver San Rafael, CA Great that you have that part in stock and thank you for your quick reply.

Press Select button to resume printing, some data loss will occur, you will need to add memory or reduce the complexity of the print job. http://upintheaether.com/hp-laserjet/hp-4100-error.php Is it a possibility one of the other sensors could have gone bad? Remove optional I/O PCA, then re-test. 69.x SERVICE 4000/4050/4100/5000/8000/8100 1. Replace Cable, Laser/Scanner to DC Controller cable. (P/N RG1-0908-000) II, IID, III, IIID Only: 1.

At least one of two tabs must be present. Scroll through items until "I/O =" appears and use the +/- key to display parallel and the enter key to select. Replace Fuser Assembly. Check This Out Check entire paper path, check all sensors and flags. 13.21/13.33 Door open jam. 8000/8100 Only: 13.1 Paper late jam at PS2. 13.2 Paper delay jam at PS1 13.5 Fuser output, paper

eCommerce Solution : k-eCommerce Click here to purchase the laser scanner assembly. ERROR 14 No EP Cartridge or No Toner Cartridge No toner cartridge or cartridge not fully seated - pull it out and install it again.

Replace formatter PCA. 60, 61, 63 MEMORY ERROR IIISi/4Si Only: 1.

Privacy Policy Terms of Use On Sale About Us Contact Us Order Status FREE TECH SUPPORT (877) 755-5300 Login My Cart (0) Printers Printer Supplies Printer Parts Printer Accessories Error Codes Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand Bad Paper Input sensor (PS1). 2. Inspect Fiber-Optic Cable between Laser/Scanning Assembly and DC Controller. 3.

ERROR 67 Defective formatter PCA On the 4Si this could be a temporary error which can be corrected by cycling the power 4V/4MV - This can also be a temporary error Can also be caused by a defective DC controller. ERROR 40 Make sure computer and printer are set to the same baud rates. http://upintheaether.com/hp-laserjet/hp-4100-service-error-codes.php Add memory or simplify print job. 21 ERROR/PRINT OVERRUN/PAGE TOO COMPLEX 1.

Bad drive gears. Check Fan 1, replace if necessary. 57.3 ERROR 1.