Hp 3055 Error Codes
You can determine which one by plugging them back in one at a time (cycling the power each time – never plug or unplug an accessory with the printer powered on). Check the main motor’s cable to ensure that it is seated properly. 4. Replace the EIO card or Network card.10. If either Step 1 or Step 2 cleared the error, there is a good chance that the cause was a driver problem (the printer driver is the software on the computer have a peek here
HP LASER PRINTERS 3SI, 4SI, 4V 1. Replace scanner ass'y. 4. If after replacing the formatter, the error persists, replace the DIMMs. Temporary communication error. 2. http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=1161389
Hp Laserjet 3055 Scanner Error 3
The product could not be added to your profile at this time. controller ass'y HP LASER PRINTER 4345MFP, 5025MFP, 5035MFP ERROR 52.XY 1. Reseat the formatter and the firmware dimms chip.3. Replace the firmware DIMMS.11.
Software error- try printing from a different software. 5. If the error persists, replace the laser scanner assembly.HP LASER PRINTERS 4200, 4300, 4250, 4350 ERROR 52.XX 1. PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My Try again later No fax answer.
The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 51.X PRINTER ERROR A loss of beam-detect HP LASER PRINTERS 3015/3020/3030MFP 1. Remove all accessories (ex. Wird verarbeitet...
Up grade the firmware dimms or replace the firmware dimms.7. The four characters after the decimal point are the firmware address at which the error occurred. Check the fan’s connector and make sure the fan is not blocked. 2. Replace the I/O card or the Network card..
Hp Laserjet 3055 Manual
These products are now supported by Hewlett Packard Enterprise. low 1 copy. Hp Laserjet 3055 Scanner Error 3 The page containing the error will automatically be reprinted. 2. Hp Laserjet 3055 Scanner Driver For Windows 7 controller ass'y HP LASER PRINTER 9000, 9040, 9050MFP 1.
Learn more » Quality Rebuilt Fusers Every LPT remanufactured fuser is tested and inspected. http://upintheaether.com/hp-laserjet/hp-laserjet-3055-error.php We recommend starting with the firmware SIMM or DIMM, since this is the less expensive alternative. Try using the parallel interface, and printing threw the parallel cable to test the mother board.7. DIMM, EIO card).
If you cannot clear the error, you may have to physically replace the firmware SIMM or DIMM (see Step 5). Kategorie Wissenschaft & Technik Lizenz Standard-YouTube-Lizenz Mehr anzeigen Weniger anzeigen Wird geladen... Remove and reinstall the formatter.5. Check This Out You can determine which one by plugging them back in one at a time (cycling the power each time – never plug or unplug an accessory with the printer powered on).
The 49/79 Error in HP LaserJets The 49/79 error is not the most common problem that you will see in a laser printer (that would be the 13 Paper Jam), but Wird geladen... Either the formatter board or something plugged into this board is bad.
Update the firmware to the newest version. 5.
This product has been successfully added to your profile. HP LASER PRINTERS 1200, 2200, 3100 FAX, 3200 FAX, 4100 1. See that article for full details, but in brief, the printer’s formatter board is a computer of sorts, and firmware is the program that tells the formatter board what to do Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations
Try using the parallel interface, and printing threw the parallel cable to test the mother board.7. Try printing a job from a different software program. 4. Replace the toner cartridge.3. this contact form Make sure that all flat, flexible cables (FFCs) are properly 5.
The four characters after the decimal point are the firmware address at which the error occurred. If you get down to the bare minimum (formatter with only the firmware SIMM or DIMM plugged into it) and still cannot clear the error, all that is left is to Now perform a cold reset (details of this procedure differ for different printer models – consult the appropriate service manual). Replace laser scanner ass'y 3.
X = description: 1 = Illegal input or bad accessory connector 2 - Illegal output The page containing the error will automatically be reprinted. 1. Check the FFC connection between the formatter and the scanner. 4. With the network removed, Perform a cold reset.9. Try the DIMM in another slot. (The firmware DIMM must remain in slot #4—the lowest DIMM slot.) 3.
If the problem persists, reseat the firmware memory card.4. The printer has experienced an internal firmware error. 2. All Rights Reserved. Replace scanner cable to the D.C.
The page containing the error will automatically be reprinted. 2. Turn the printer off and then turn the printer on.2. Scanner start up error 2. Replace the D.C.
Turn the power off and wait for 30 seconds, then turn the power back on. 2. But the more you know about what the code means and what kinds of things can cause it, the better equipped you will be to troubleshoot it. if the error persists, upgrade the firmware. Wird verarbeitet...
X description: 4 = Printer fan 7 = Duplex fan 1. Temporary error.Laser scanner error/start up/rotation error 2. Replace the power supply.