Home > Hp Laserjet > Hp 3005 Error Message

Hp 3005 Error Message


by moe on Sep 17, 2009 at 10:13am Add comment Please sign in to comment 0 Thanks for the suggestion! by unknown on Apr 29, 2009 at 3:32pm Add comment Please sign in to comment Downloading firmware will not fix this problem. Try to determine whether the error occurs intermittently, while printing, or when turning on the device. 3. Didn't get many electronics faults when the printers were mainly manufactured in the US and Japan! Source

Saw doc id : emr_na-c01143533-2 As per the doc the Formatter board & the memory needs to be replaced. Initializing This message appears when the device is turned on and begins initialization. HP has really gone downhill over the last 2 years when it comes to customer support and do not count on it getting better. So far the results have been good.

Hp P3005 Memory Error Replace Dimm

The device EIO card in slot X has overflowed its I/O buffer during a busy state. by Stephen on May 20, 2009 at 7:02am Add comment Please sign in to comment I tried c01215806-Q7814A but got nowhere. During this time, no jobs can be printed. If the problem persists, contact HP Support.

I throw the printer rather out of the window. by opcso on May 8, 2009 at 1:43pm Add comment Please sign in to comment 0 I had a warranty center replace my formatter under a service note # C01215806 since by Haelge on Apr 22, 2008 at 2:52am Add comment Please sign in to comment 0 check this outhttp://partsurfer.hp.complug in Q7848-61003(network/usb) or Q7847-61003(usb/parallel)Hope this helps.GEOP.S. Hp Laserjet P3005 Memory If you have other tech support questions that are not covered here, send email to [email protected]

Lower rear door completely, and then remove all media found. No action necessary. TRAY XX EMPTY alternates with Ready The tray is empty, but the current print job does not require this tray. I have just loaded the latest firmware on to the 70 or so P3005 printers on our network as recommended in various HP bulletins and the jury is still out.

Press (HELP) for help. P3005 Formatter Board If you want take a look at the COOPER Hand Tools Website http://www.cooperhandtools.com/brands/weller/index.cfm or if you can read german here: http://www.jbctools.com/pdf/Catalogos/Advanced/CatAdvAle.pdfYou can find there a lot of special desoldering heads. If there is anything plastic that looks like it might melt and can come off, remove it.http://en.wikipedia.org/wiki/Solder by moe on Oct 13, 2009 at 12:25pm Add comment Please sign in to Event Log Empty SHOW EVENT LOG was selected from the control panel, and the event log is empty.

Hp P3005 Cold Reset

It is the defective TOSHIBA chip on the top middle of the formatter board & usually there is a white sticker over the chip. http://onedira.blogspot.com/2010/09/how-to-handle-494c02-errors-on-hp.html Parts qualified : Q7848-61003 PCA - OTHER : LJ P3005N PCA 02.039.3 CB421-67951 Memory (DIMM) : 64MB, 144-pin, DDR2 SDRAM DIMM memory module by calderdale on Jul 31, 2008 at 5:35am Hp P3005 Memory Error Replace Dimm by opcso on Sep 2, 2009 at 12:01pm Add comment Please sign in to comment 0 Called HP and they would not do anything except refer me to a local service Hp Laserjet P3005 Hangs During Startup by unknown on Nov 13, 2009 at 3:14pm Add comment Please sign in to comment 0 Good luck with that, both the class action and your decision to go with those

Press (SELECT) to continue. http://upintheaether.com/hp-laserjet/hp-4200-error-message.php If a critical error persists, service is required. The message appears while the job is stopped, the paper path is flushed, and any remaining incoming data on the active data channel is received and discarded. No action necessary. Hp Laserjet P3005 Troubleshooting

Reinstall the firmware. The device can print with this supply, but print quality might be affected. immediately has the same error. http://upintheaether.com/hp-laserjet/hp-1012-error-message.php If the problem persists, contact HP Support.

The warranty is just a way to milk more money from the consumer in the long run and HP doesn't have to take responsibility for anything they produce.Me personally and the Hp Laserjet P3005 Replace Dimm 1 by opcso on Nov 18, 2008 at 11:19am Add comment Please sign in to comment 0 I just recently bought a replacement (Brand New) P3005DN off EBAY for $450 & saw Service or repairs that are required as a result of using non-HP supplies are not covered under HP warranty.

Seems the problems persist with this board no matter how many revisions they make to it, and it is not just with the toshiba IC, the one i have has the

by HP-Printer-Dave on Nov 18, 2008 at 10:20am Add comment Please sign in to comment 0 This problem goes way beyond the Toshiba chip. Can you not make a reliable printer anymore ???? Unauthorized supply in use alternates with Ready The device has detected that a non-HP supply is currently installed and (SELECT) (override) was pressed. Hp Laserjet P3005 Service Manual If the message persists after exiting help, turn the device off and then on.

Any button press or the receipt of data clears sleep mode. by opcso on Aug 14, 2009 at 5:51am Add comment Please sign in to comment 0 Hi,I had the problem with the formatter board where the paper jam and toner lights by opcso on Dec 22, 2008 at 7:02pm Add comment Please sign in to comment 0 Has anyone tried the heat gun (hairdrier) and has it been a success? Check This Out I cannot take credit for this, as I mentioned before I only tried this after reading through all of these posts.

Reinstall the firmware. Reinstall the duplexer. Generated Mon, 17 Oct 2016 21:23:36 GMT by s_ac15 (squid/3.5.20) Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets Is this the current, correct document number?

Copy the firmware, usually it has .rfu extension to the firmware update utility. USB Storage not functional The USB storage device is not working. Respond to this 1 Boy, I am going to try the heat gun or hair dryer on my jetdirect 615 cards that are out of the serial # range for the