Home > Hp Laserjet > Hp 2015dn Error Lights

Hp 2015dn Error Lights

Contents

From the hp website it looks like the light pattern is telling me there may be an engine error or Fan motor error. on November 5, 2010 at 3:40 PM At 175 degrees Celsius: Circuit board baked, Worked at first try! :-)/[email protected], Sweden Venkatakrishnan said... on May 21, 2012 at 12:56 AM This little trick has worked for us :)Same situation and followed the procedure precisely - printer is now back up and running. I have a couple dead JD 610n cards I'm going to try as well. Source

Cooled for about 25-30 minutes. I'm assuming the board is what I see when I open the little 3x5 inch hatch in the center of the left side of the machine. HP appears to have been sold out for the past several weeks and no longer even lists a price in their HP parts store for some reason. Here is the caveat - I have to provide a credit card number for them to charge the full replacement(new price, $400 not the refurbished pricing)which will be held until they

Hp Laserjet P2015 Paper Jam Light Stays On

on October 31, 2013 at 7:34 AM Thank you very much!I tried the same on a P2015dn where the paper light was stuck (with orange light), now it works again! on December 23, 2011 at 6:05 AM Brilliant!!!! 100% Thanks for your help.Owen Anonymous said... on April 19, 2013 at 6:13 PM This method still works flawlessly.

This one never finished booting. Since the main board you fixed doesn't actually get hot, then you may have achieved a permanent fix just though sheer luck. on October 24, 2010 at 11:13 PM Printer was dead for a year. Hp Laserjet P2015 Manual Using this forum I found that I had lots of company and I needed a replacement formatter board - so I did it myself and all was OK other than the

However, they were VERY helpful in talking through my options with me, spending significant time and ultimately recommending I buy a replacement printer through another retailer (they sell higher-end business printers).The Hp Laserjet P2015 Attention Light Blinking Preheat oven to 400 degrees and bake the formatter for 5 minutes. Once your eight minutes is up, turn off the oven and open the door to let it cool in place. You'll want to remove the memory module too if you have one installed.

It would have to be POR-ed whenever I needed a printout.Finally after another 8 months, the NEW formatter board went into "two lights" mode. Hp Printer Error Symbols This is a pretty simple fix. Avoid dropping the board while hot - this could cause some parts to fall off the board. It just jumped back to life after baking.

Hp Laserjet P2015 Attention Light Blinking

I just wish someone knows how to force a firmware update.

Wird verarbeitet... Hp Laserjet P2015 Paper Jam Light Stays On They immediatly informed me that if it wouldn't take either of those resets then it would definetly be the formatter board (Q7804-60001 for the standard base version of the Laserjet P2015), Hp Printer Symbols What Do They Mean HP gave her a bit of push back on "this type of warranty repair," but she beat them into submission and I got my printer back in 2 days.

It doesn't work with hot air furnaces :( Will need to find someone with an old fashioned oven Or use the grill option of the hot air furnaceI preheated the hot this contact form Hey presto its working. I finally decided I had nothing to lose. Startup issues in general. Hp Laserjet P2015 Error Lights (leds) Stuck On

I removed the formatter, placed it face down on three ball of tin aluminum foil on a cookie sheet and baked it at 350F for 8 minutes. Thanks to everybody here who initially suggested this and then gave positive feedback that it worked and no thanks, of course, to HP! Once I was done with the physical and verbal abuse, I noticed that the motor was running briefly after powering on, as it normally does during the startup process. have a peek here I found this forum because I had the same jam light stuck on, no network response, most likely the formatter board problem.I removed the formatter board and followed moe's suggestions above

Anonymous said... Hp Laserjet P2015 All Lights On Except Paper Found this thread, cooked it about 30 min ago, now she'sa printing fine. As with many similar chips, especially early designs it seems, the failure is likely an open circuit due to a break in one of the solder balls from repeated thermal stress.

by unknown on Nov 4, 2009 at 8:10am Add comment Please sign in to comment 0 It works. 350 degrees F for 8 minutes.

After finding that this error code is not listed in the service manual, I tried doing a cold reset, and then an NVRAM reset. From HP's support forums there is supposed to be a way to send the serial number the same way you would a firmware file via FTP or LTP, but time constrants Thank you! Hp Laserjet P2015 Paper Jam Light Blinking From what I understand this is the same problem that Microsoft has with the XBox 360.With a pile of 25 broken ones you've got some serious baking to do.What do you

However, it is possible. Each time, the hardware crapped out on us just a month or two after the printers' warranties had expired.I was VERY skeptical about putting a board in the oven, but after I have 25 of them sitting in my repair room with the same problem. http://upintheaether.com/hp-laserjet/hp-2015dn-paper-jam-error.php Before I found this forum, I did a firmware update when it was in a working state.

Either that or the networking died and he/she uses it locally anyway so it doesn't matter. Just finished cooking my Formatter Board for the recommended 8 minutes at 350F. I will keep everyong posted. by unknown on Oct 21, 2009 at 1:14pm Add comment Please sign in to comment 0 @moomanIf you do a search for P2015dn formatter board on ebay, you'll likely see a

If it doesn't work after we bake it, then we still have the large paper weight that we had before only it smells like cookies! santi said... Kai Gillmann said... Shake off the cover, Back the board...

It is like this: the solenoid won't work, the resistance is high (That is no conductivity) indicates an open circuit, most likely the solder ball (same problem as the IC formatter on May 9, 2013 at 8:55 PM use a Hakko Heat Gun set to 370Chttp://www.amazon.com/Hakko-Heat-1300-Watts-Temperature/dp/B000BN2ZZYLesser risk of damaging the coil, battery or whatever discrete components in the board. You're going to think this is a late April fool's joke, but it's actually not.