Home > Hp Laserjet > Hp 1200 Error Lights

Hp 1200 Error Lights

Contents

Do not hold the button down. HP Customer Support Z7_3054ICK0KGTE30AQO5O3KA30U7 hp-contact-secondary-navigation-portlet Actions ${title} Loading... When the lights begin to blink, press and hold both the On/Resume button () and the Paper Size button at the same time. Step one: Disconnect and then reconnect the USB cable Disconnect the USB cable from the rear of the product. Source

Check the control panel to make sure that the lights are no longer blinking. IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - Anonymous Contact HP Product Context View Support Home Test page Product Home Product Warranty Result Click Download next to the full feature driver (recommended), or click Basic Drivers for other driver options. Figure : Lower the paper tray You might have to press the On/Resume button () again to resume the task. click for more info

Hp Laserjet 1200 All Lights On

Wait 30-35 minutes and then try to print another engine test. anybody by Rick on Jun 4, 2003 at 8:53am Add comment Please sign in to comment 0 Do i have hold when i press on the go button or just press note: If the alignment page fails to print, repeat the button-press sequence in this step. Check the electrical outlet to make sure that the power cord is securely plugged into it.

Dip a swab in the clean water, then squeeze it to remove most of the moisture. Gently lower the tray until it is horizontal and stops. Figure : Reinsert the cartridge Firmly push the cartridge in until it snaps into place. Hp Laserjet 1200 Fatal Error Give it a LIGHT tug and if it comes out of the connector it needs to be reseated.Fixed mine by Anonymous on Oct 10, 2007 at 3:34pm Add comment Please sign

If these steps resolved the issue, you do not need to continue troubleshooting. Use only one type of paper at a time. Modify your browser's settings to allow Javascript to execute. When only the On/Resume button () is blinking, release both buttons.

The printer is turning on or off or processing a print job, or a print job has been cancelled. Hp Laserjet 1200 Yellow Light Blinking If the issue persists, continue to the next solution. Paper was added to a stack already in the tray while the HP product was printing. pls help by unknown on Nov 2, 2011 at 7:26am Add comment Please sign in to comment 0 Balican: This thread is for the HP Laserjet 1200.

Hp Business Inkjet 1200 Error Lights

Solution two: Make sure that the front panel overlay is installed correctly If the front panel overlay, or bezel, is incorrectly installed, the product may indicate a false carriage stall error http://h20564.www2.hp.com/portal/site/hpsc/public/psi/troubleshootResults?sp4ts.oid=29789 The Power light and the Door Open light are on. Hp Laserjet 1200 All Lights On Fold out the paper tray extender to catch paper as it exits the device. Hp Laserjet 1200 Blinking Orange Light Figure : Clean the paper feed rollers Allow the rollers to dry for 10 or 15 minutes.

Solution two: Check the connection between the All-in-One and the computer Follow these steps to make sure that the USB cable is securely connected to the product and the computer. this contact form A message indicating that the carriage is stalled might appear on the computer. If the product is unresponsive for more than 60 seconds, continue to the next solution. If you have added any additional memory, take it out and try powering on without it. Hp Laserjet 1200 Troubleshooting

If the issue persists, continue to the next solution. Figure : The location of the carriage contacts Figure : The gold-colored electrical contacts inside the carriage Wait about ten minutes to allow the electrical contacts to dry, or use a Press the On/Resume button () to turn on the product. have a peek here Torn, wrinkled, or damp paper loaded in the paper tray.

Reconnect the power cord to the rear of the product. Hp Business Inkjet 1200 Printhead Light Blinking This page requires Javascript. Solution four: Service the All-in-One If you have completed all the steps and are still experiencing a problem, continue to the Service the All-in-One section at the end of this document.

Don't show me this message again.

Figure : Check the electrical connections Press the On/Resume button () to turn on the product. Thank you! Go to HP Customer Support - Software and Driver Downloads. Hp Business Inkjet 1200 Manual Figure : The rollers in the rear access door Gently push the pins on the right end of the rear access door into the holes on the right side of the

Only add paper to the tray when the product is not printing. Solution seven: Replace defective cartridge One of the cartridges might be defective. With the power on, disconnect the power cord from the rear of the product. Check This Out caution: Do not remove jammed paper at this stage.

Click here to skip to Step 3 below - you only have to perform the steps on the problem cartridge. The reset is now complete. If these steps resolved the issue, you do not need to continue troubleshooting. Solution three: Perform a partial reset A partial reset returns the user settings to their factory defaults.

If these steps resolved the issue, you do not need to continue troubleshooting. If the message on the computer indicates a specific cartridge, that is the problem cartridge. If the lights on the control panel still blink, continue to the next step. Z7_3054ICK0KGTE30AQO5O3KA3015 hp-online-communities-portlet Actions ${title} Loading...

Press and then quickly release the On/Resume button () to start a power on/off cycle. Make sure that the length and width adjusters on the tray are correctly positioned, and then push the stack of paper forward until it stops in the tray. Follow these steps to clear any jammed paper. Press the cloth against the paper feed rollers, and then rotate them upwards with your fingers.

Press and release the Color Start Copy button. Z7_M0I02JG0KONJ30ACBBF8MM1084 hp-hero-support-search Actions ${title} Loading... The Power light is on and one or more color indicator lights blinks. Paper jam causes The following factors can cause paper jams: Paper loaded incorrectly in the paper tray.

Clean the print cartridge contacts. Press the Cancel button () on the control panel. The carriage moves to the center of the product. If you can pull it from the rear of the product or the tray, always try the rear first.

If the issue persists, continue to the next solution. Press the Cancel button () on the control panel. Figure : Press the Scan button to begin the alignment The alignment is complete when the On/Resume light () stops blinking. Figure : Disconnect the power cord Wait 15 seconds.