Hp Error Code 50.2
Is this something I can handle myself? If you were getting the error before, then you may have an issue with your dc controller or low voltage power supply. It can be tight on both sides so a small flat tip screwdriver moving a little at a time from each side will release it. Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations http://upintheaether.com/hp-error/hp-error-code-24-10.php
Easy to replace, just drop down the back cover, release the plastic strap which holds the door from falling down, move to one side and the back comes off. I'm new to the forum, and hoping you can help.My trusty HP Laserjet 5000n is posting an error message "50.2 Fuser Error." HP wants $900 to fix it, which sounds excessive. Reply 0 0 KennyB3 Master's Graduate Posts: 350 Member Since: 10-17-2011 Message 4 of 4 (1,041 Views) Report Inappropriate Content Re: lj CP1515n error 50.2 Options Mark as New Bookmark Subscribe If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message.
PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My There are many ways to contact HP. I can supply that and a video that shows how to install it. by sfe39 on Jan 18, 2006 at 4:20pm Add comment Please sign in to comment I don't know if you read my reply, but I run the fixyourownprinter site.
I will have to think about it. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, If the 50.2 Slow Fuser error message returns, it's time to replace your fuser. Thank you! Register · Log In HP Support Forum Home > Printers > LaserJet > hp laserjet 4250n 50.2 fuser error HP Support Forums Join in the conversation.
If no, then you got a defective fuser and you need to return it for replacement. The screen says to turn it off, then back on and if the issue persists, to call a tech. Thank you! Register · Log In HP Support Forum Home > Printers > Inkjet > 50.2F.00 fuser error HP Support Forums Join in the conversation. Heck you could even order a maintenance kit from hp for a lot less money.
Click the Kudos on the left side for helping and click Accept as Solution for providing a solution. weblink and may not be used without advance written permission of PrinterTechs.com, Inc. It was a little tough getting one of the connectors off! (not on your video), so, what i did was to carefully snap off the plastic clips with a small scewdriver, You can get reconditioned fusers from partsnow.com or depot-america.com on advance exchange.
I tried booting it without the network cable. by roba on May 26, 2010 at 12:11pm Add comment Please sign in to comment 0 http://www.fixyourownprinter.com/specials/parts/fusers/S113 by moe on May 26, 2010 at 1:39pm Add comment Please sign in to by moe on Jan 18, 2006 at 4:36pm Add comment Please sign in to comment 0 I have replaced the fuser. navigate here I can open the top cover and close it and it prints right.
First Time Here? It's cheaper to replace just that than a whole fuser. See links below for purchasing information.
PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My
Remove 2 screws and the fuser slides out. I sure do like the printer. - roba Please sign in to comment HP DesignJet 430 Buy discount ink Buy this printer More HP questions © Copyright 2011-2016, FixYourOwnPrinter.com, Inc. Tried all ways of going around it but failed . But NOT worth $900 for HP to fix it.
Open the printer remove the toner and inspect the page, if the ghost is visible before fusing, the the problem is being caused by the toner cartridge.If the page looks good I'm getting aquote on a fuser, and hope to install it myself in the next couple of days. by darrell fuller on Apr 25, 2007 at 8:37am Add comment Please sign in to comment 0 I don't know why it would work when you open and close the cover, http://upintheaether.com/hp-error/hp-error-code-49-4.php Then flip the fuser over to the right side (the non-gear side) and press in on the other fuser tab to make sure it is also fully clicked in place. (right
Click on my name and email me for pricing and ordering info. Call us with any questions, toll free 866-352-7108 or local 608-831-2396 Purchasing information : HP Color LaserJet 2820 , 2840 fuser and maintenance kit Installation instructions: HP Color LaserJet 2820 , by mharris on Jan 18, 2006 at 3:33pm Add comment Please sign in to comment 0 That is indeed a fuser error. NOTE: On this model, it is very easy to change out the fuser.
HP estimates average fuser life to last about 100,000 pages; but a fuser can fail much earlier depending on printing conditions, heavy paper jams, and the quality of the fuser installed. If my post resolves your issue please click the accepted as solution button under it.To thank a Tech for a post click the thumbs up button under the post.You can even One of the good numbers to call is 1-800-474-6836 and select the options for the printer. PrinterTechs.com 608-831-2396 or 866-352-7108 About Us Contact Us Search Products Search Support All Products PrintersHewlett PackardLexmarkCables and Misc.JetDirect CardsBrotherKyoceraDell Toner Maintenance Kits Printers Parts Tech Support Account Login Shopping Cart My
out real well. and an instructional cd. The fuser comes as part of a maintenance kit. We have installation instructions available, see the links below. Not really too tough to replace, with any technical skill.