Home > Hp Error > Hp Error Code 48

Hp Error Code 48


Error 30 PS Error 16 ALL PRINTERS This is an unexpected PostScript firmware error. Can also indicate a mis feed or paper not being picked up. Create your Spare Parts List. Feel free to add comments and suggestions about this Knowledge Base article. http://upintheaether.com/hp-error/hp-error-code-24-10.php

Look for smooth or cracked worn surfaces. The same happens when I try to scan, copy or fax. I will send the information to you for a reset via private message. Replace this as an assembly. http://h30434.www3.hp.com/t5/Inkjet-Printing/Error-code-48/td-p/2473847

48.a1.01 Job Accounting Service Error

Back back to top How did we do? Make page less complex and retry. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Switch the power off from the back of the product and disconnect the power cord.

A switch on this assembly may not be activated properly. after I did a few prints. Lets see how many I can print tonight astomorrow is a new day :-) Logged If you buy a camera, you're a photographer... System resets but when I try to print the display shows "printing" but nothing happens.

What happened? Hp Error 49 Turn the printer off/on to attempt to clear or reset the message. If there is no newer firmware, then the workaround is to downgrade firmware on the device. See on page 96. – If the test finds that the ink supply is defective, replace it. – If the test does not find any errors, remove all the ink supplies

Defective Paper Control Sensor PCB - These do fail and will need to be replaced. If you are using usb, how long is the cable? More info… 13.3 Resolved 13.4 420004 Pauses during printing, or slow copy/print/panel performance. More info… Resolved 13.2.22278 420006 “Cannot connect to the quota server” errors when copying.

Hp Error 49

On the 5L, set the Enhanced I/O to AUTO (PCL mode) and resend the print job. https://www.papercut.com/kb/Main/KnownIssuesHPFutureSmartEmbedded Let me know how it goes. 48.a1.01 Job Accounting Service Error Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. Member Offline Posts: 397 Re: HP z Error code 48:00 « Reply #5 on: January 11, 2015, 09:35:20 PM » A year or two ago my Z3200 started displaying this error.

View Solution. http://upintheaether.com/hp-error/hp-error-code-54-2.php Thank you! Register ยท Log In HP Support Forum Home > Desktops > Hardware > unknown error (48) HP Support Forums Join in the conversation. The information contained on this chip is dependent on the printer model and the supply. This board takes the input from the two sensors and provides info to the DC controller.

Any help here would be appreciated too. Back back to top How did we do? Logged If you buy a camera, you're a photographer... http://upintheaether.com/hp-error/hp-error-code-49-4.php ERROR 89 All Printers (except 5L/6L) The PostScript ROM's have bent or broken pins inspect the pins and reseat if necessary Check to see that the ROM SIMM's are in the

You can talk to any agent and they should be able to help you. Error 55 On IIISi/4Si Printers this is due to the DC controller not receiving the proper information upon startup. We got it this morning and I have it installed.

Your cache administrator is webmaster.

I ran the "HP Hardware Diagnostic Utility" and it reports :Your printer is in the following state:Unknown error (48)What can I do? Don't show me this message again. Reseat DIMM, then Formatter - Replace or flash DIMM then formatter Back back to top How did we do? If an error appears after installing a supply, the last supply you installed is defective.

Back back to top How did we do? LJ 4250/4300/4350 A printer fan is not funtioning. Check and reinstall. his comment is here Defective High Voltage power supply or on the LJ II/III the DC controller to High Voltage power supply can be defective.

x = description 1--printer fan 1. When I reboot it is clear. Reset as needed. Can also be formatter PCA.